background image

Chengdu Ebyte Electronic Technology Co., Ltd.

E19-433M20S2 User Manual

Copyright ©2012–2020

Chengdu Ebyte Electronic Technology Co.,Ltd.

6

affect the performance. It is recommended to keep them away from the module according to the strength of the

interference. If necessary, appropriate isolation and shielding can be done

Assume that there are traces with large electromagnetic interference (high-frequency digital, high-frequency analog,
power traces) around the module that will greatly affect the performance of the module. It is recommended to stay
away from the module according to the strength of the interference.If necessary, appropriate isolation and shielding
can be done.

If the communication line uses a 5V level, a 1k-5.1k resistor must be connected in series (not recommended, there is

still a risk of damage)

Try to stay away from some physical layers such as TTL protocol at 2.4GHz , for example: USB3.0

The mounting structure of antenna has a great influence on the performance of the module. It is necessary to ensure
that the antenna is exposed, preferably vertically upward. When the module is mounted inside the case, use a good

antenna extension cable to extend the antenna to the outside

The antenna must not be installed inside the metal case, which will cause the transmission distance to be greatly
weakened.

4.2 Software editing

SX1278/PA+LNA

same drive way as SX1278/SX1276

user can refer to SX1278/SX1276 datasheet.

DIO0

DIO1

DIO2

DIO3

DIO4

DIO5 are configurable I/O ports for various application

see more in SX1278

datasheet. It can be floated when not used.

RST

TXEN

RXEN must be connected,among which RST control chip reset

TXEN, RXEN are for controlling RF

switch.

Make it ground well with large space for grounding and small power ripple. Filter capacitor is necessary and make
sure it is close to pin VCC and GND.

SPI communication rate should not be set too high, usually around 1Mbps.

In transmitting

set TXEN as high communication level

RXEN pin is low level; In receiving, set RXEN as high

communication level,TXEN is low level; Before powering off, set TXEN

RXEN as low level.

Re-initialize register configuration when the chip is idle for higher stability.

Summary of Contents for E19-433M20S2













Reviews: