EBS CPX200NB Installation And Programming Manual Download Page 56

Page: 56 / 116

CPX200NB ALARM CONTROL UNIT – INSTALLER MANUAL

56 / 116

PROGRAMMABLE PARAMETERS

Parameters available in configuration wizard were divided into groups: Access, Transmission,
Inputs/Outputs, System Options, Users, Monitoring, Restrictions, SMS Notifications, Link

Control, Firmware. Each of the groups will be described in detail further on.

8.1.

ACCESS

8.1.1.

Parameters

8.1.1.1.

Equipment operation mode

Depending on user’s preferences, the equipment can operate in one of 4 modes (to
be selected from a drop list):



GPRS & SMS: GPRS transmission (TCP/IP protocol) in standard and in case of

problems with that connection, automatic switch into SMS mode



SMS: Transmission only in SMS mode without the attempt of establishing a GPRS

connection



GPRS: GPRS transmission (TCP/IP protocol) in standard. In case of any problems

with that connection, no remote connection is possible



No server connection: no transmission with server, remote communication with a
user is possible only via SMS messages

Summary of Contents for CPX200NB





















































































































Search results

Summary of Contents for CPX200NB

Reviews:

Related manuals for CPX200NB

Brands by name

Popular brands

EBS CPX200NB, Installation And Programming Manual

Search results

Summary of Contents for CPX200NB

Reviews:

Related manuals for CPX200NB

Brands by name

Popular brands