EBS Ink-Jet Systeme GmbH
D-51588 Nümbrecht-Elsenroth, Germany, Alte Ziegelei 19-25
+49 (0)2293-939-0,
+49 (0)2293-939-3
e-mail: [email protected]
4
signature: 2010/02/00086#1 EN
ed. March 24, 2010
2
NOTE
!
In order to use the printer characteristics fully, please follow all the recommendations contained in this
description. If any of the hints is not followed, a malfunction of the printer may occur or part of the printer's
functionality may be lost, whereas in extreme cases permanent damage that is not covered by guarantee
may occur.
Climatic conditions:
operating temperature from +5°C to +40°C,
relative humidity up to 90% without condensation.
Mechanical conditions:
vibration of max. 1 g, at max. 10 Hz, impact of max.1 g, over max. 2 ms.
Tools required:
cross point screwdriver, 5 mm imbus key
I
MECHANICAL INSTALLATION OF PRINTER IN WORKPLACE
S
T
E
P
1
Install the printer on stand
24
in any convenient position in a
place that is free from vibration, shocks, excessive dust,
smoke and dirt as well as from aggressive or inflammable
vapours and gases.
If the printer is to be operated in a heavily dusty or
contaminated environment, please consider whether an
additional filter should be used in order to protect vent valve
4
or whether a cover allowing free airflow should be installed
(ask your dealer for optional accessories).
Install and operate the printer in such a position that the line
determined by the top housing edge of controller
1
shows the
HORIZONTAL DIRECTION,
whereas the butting face of the
head shows the VERTICAL DIRECTION (see
Fig. 2
).
NOTE:
The printer must not be tilted in any direction by
greater an angle than 30° while it is being installed
and operated.
HORIZONTAL
DIRECTION
VERTICAL
DIRECTION
11
23
6
1
24
25
Fig. 2
S
T
E
P
2
Install internal photo-detector
19
in holder
18
on print head
6
or in any other place that will allow
you to release printing conveniently within the reach of photo-detector cable (see
STEP 3
). The
holder can be put on the other side of the head, if need be, by unscrewing the holding down bolts
and reversing the holder
18
.
S
T
E
P
3
(
O
pt
io
na
l)
You can fix an (external) photo-detector in a required place and attach it to connection socket
15
which is on the back panel.
You can also install a conveyor speed converter, a so called shaft-encoder, in a convenient place
on the conveyor on which objects to be labelled will move, so that the converter is driven by the
conveyor. Connect the shaft-encoder to socket
16
which is on the back panel.
S
T
E
P
4
Remove protection
7
and screw in head slide
8
in place of it. Install cover
12
. Screw blue bottle
11
to the printer bottom to collect ink slops (make sure that the printer is not tilted by greater an
angle than 30° from the vertical direction). Remove protective film from panel LCD
2
.
NOTE
: The use of the slide is obligatory and vital for the proper operation of the printer!
S
T
E
P
5
Connect the controller feeder cable to socket
13
and to a mains socket and then start the printer
– by pressing switch
10
on the right wall of printer controller
1
for a short time. Wait about 60
seconds for the printer system to start.
II
MAKING READY FOR PRINTING
S
T
E
P
6
Check whether air filter
21
situated in vent valve
4
is clean. The filter is unscrewed and screwed
in as it is shown in
Fig. 1
.
If the filter is dirty, clean it (see
Basic Service Hints
below). When the filter is clean, open valve
4
by turning the valve cap by about 15° counter clockwise - see
Fig. 1
(the valve is open when
mark
22
on valve
4
indicates the
PRINTING
position).