Operating instructions
W6D800-DD01-35
Translation of the original operating instructions
3.2 Nominal data
Motor
M6D138-LA
Phase
3~
3~
Nominal voltage / VAC
400
400
Wiring
Δ
Y
Frequency / Hz
50
50
Method of obtaining
data
ml
ml
Valid for approval/
standard
-
-
Speed (rpm) / min
-1
880
670
Power consumption / W
1940
1210
Current draw / A
3.9
2.23
Max. back pressure / Pa
160
92
Min. ambient
temperature / °C
-40
-40
Max. ambient
temperature / °C
60
60
Starting current / A
13
4.3
Max. safe operating
speed (rpm) /
min
-1
1100
@ 70 °C
1100
@ 70 °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Technical description
Weight
42 kg
Size
800 mm
Motor size
138
Rotor surface
Painted black
Terminal box material
PP plastic
Blade material
Sheet aluminum insert (painted black),
sprayed with PP plastic
Support ring material
Steel, coated with black plastic (RAL
9005)
Fan housing material
Sheet steel, galvanized and coated with
black plastic (RAL 9005)
Number of blades
5
Blade pitch
0°
Airflow direction
A
Direction of rotation
Counterclockwise, viewed toward rotor
Degree of protection
IP54
Insulation class
"F"
Moisture (F) /
Environmental (H)
protection class
H2+A
Ambient temperature
note
Occasional start-up at temperatures
between -40°C and -25°C is permitted.
For continuous operation at ambient
temperatures below -25°C (such as
refrigeration applications), use must be
made of a fan design with special low-
temperature bearings.
Installation position
Shaft horizontal or rotor on top; rotor on
bottom on request
Condensation
drainage holes
On stator side
Mode
S1
Motor bearing
Ball bearing
Touch current
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
<= 3.5 mA
Electrical hookup
Terminal box
Motor protection
Thermal overload protector (TOP) with
basic insulation
with cable
Axial
Protection class
I (with customer connection of protective
earth)
Conformity with
standards
EN 60034-1 (2010)
Comment on CE
Commissioning not permitted in the
European Economic Area
Approval
EAC; VDE
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
;
Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.
3.4 Mounting data
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
Strength class of
screws
8.8
;
Secure the screws against unintentional loosening (e.g. use self-
locking screws).
3.5 Transport and storage conditions
Max. permitted
ambient temp. for
motor (transport/
storage)
+80 °C
Min. permitted
ambient temp. for
motor (transport/
storage)
-40 °C
Item no. 16320-5-9970 · ENU · Change 219827 · Approved 2021-01-26 · Page 5 / 12
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com