ebm-papst S3G300-AK13-52 Operating Instructions Manual Download Page 8

Page: 8 / 11

Operating instructions

S3G300-AK13-52

Translation of the original operating instructions

4.4 Connection diagram

Drawing preliminary!

No.

Conn.

Designation

Color

Function/assignment

CON10 L

black

Power supply 230 VAC, 50-60 Hz, see nameplate for voltage range

CON11 N

blue

Neutral conductor

CON12 PE

green/
yellow

Protective earth

GND

blue

GND connection for control interface

0-10V PWM

yellow

Control input 0-10 V or PWM, electrically isolated

10 V / max. 1,1
mA

red

Voltage output 10 VDC 1.1 mA, electrically isolated, short-circuit-proof

Tacho

white

Tach output: open collector, 1 pulse per revolution, electrically isolated

Item no. 50926-5-9970 · ENU · Change 96553 · Approved 2017-10-27 · Page 8 / 11

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com

Summary of Contents for S3G300-AK13-52












Search results

Summary of Contents for S3G300-AK13-52

Reviews:

Related manuals for S3G300-AK13-52

Brands by name

Popular brands

ebm-papst S3G300-AK13-52, Operating Instructions Manual

Search results

Summary of Contents for S3G300-AK13-52

Reviews:

Related manuals for S3G300-AK13-52

Brands by name

Popular brands