manualshive.com logo in svg

ebm-papst S2D300-AP02-50, Operating Instructions Manual, Page: 8 / 12

Share
Download
ebm-papst S2D300-AP02-50 Operating Instructions Manual Download Page 8

Operating instructions

S2D300-AP02-50

Translation of the original operating instructions

Fans installed lying flat

Make sure the cable is routed in a U-shaped loop.

Fig. 2: Fan installed lying flat, cable routed in a U-shaped loop.

Fans installed upright

When routing the cable, make sure that the cable glands are located at
the bottom. The cables must always be routed downward.

Fig. 3: Cable routing for fans installed upright.

4.3.4 Motor protection

WARNING
Device has no overheating protection

The device is supplied without any automatic overheating
protection. The device can become hot and catch fire.
→ For the version without thermal overload protector, also

install a suitable motor protection switch.

Item no. 11683-5-9970 · ENU · Change 210436 · Approved 2019-12-14 · Page 8 / 12

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com

Summary of Contents for S2D300-AP02-50













Reviews:

No comments