Operating instructions
P2E070-AA26-01
Translation of the original operating instructions
3.2 Nominal data
Motor
M2E068-BF
Phase
1~
1~
Nominal voltage / VAC
230
230
Frequency / Hz
50
60
Method of obtaining
data
fc
fc
Valid for approval/
standard
CE
CE
Speed (rpm) / min
-1
2250
2300
Power consumption / W
58
70
Current draw / A
0.26
0.31
Capacitor / µF
1.5
1.5
Capacitor voltage / VDB
400
400
Capacitor standard
S0 (CE)
S0 (CE)
Min. ambient
temperature / °C
-25
-25
Max. ambient
temperature / °C
45
50
Min. temp. of flow
medium / °C
0
0
Max. temp. of flow
medium / °C
40
40
Flow quantity / m
3
/h
0.71
0.74
Max. flow head / m
6.1
7.2
ml = Max. load · me = Max. efficiency · fc = Free-conveying
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Technical description
Weight
1.6 kg
Motor size
68
Rotor surface
Painted black
Terminal box material
Glass-fiber reinforced plastic
Pump impeller
material
Glass-fiber reinforced plastic
Agitator material
PE
Pump housing
material
Glass-fiber reinforced plastic
Cross-member material
Glass-fiber reinforced plastic
Direction of rotation
Clockwise, viewed toward rotor
Degree of protection
IP44
Insulation class
"B"
Moisture (F) /
Environmental (H)
protection class
H1+
Installation position
Vertical
Condensation
drainage holes
On stator side
Mode
S1
Motor bearing
Ball bearing
Touch current
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
< 0.75 mA
Electrical hookup
Connector with cable; Via terminal box,
capacitor integrated and connected
Motor protection
Thermal overload protector (TOP)
internally connected
with cable
Lateral
Protection class
I (with customer connection of protective
earth)
Motor capacitor
according to EN 60252-
1 in safety protection
class
S0
Conformity with
standards
EN 60335-1; CE
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
;
Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.
3.4 Mounting data
;
Secure the screws against unintentional loosening (e.g. use self-
locking screws).
Strength class of
screws
8.8
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
3.5 Transport and storage conditions
Max. permitted
ambient temp. for
motor (transport/
storage)
+80 °C
Min. permitted
ambient temp. for
motor (transport/
storage)
-40 °C
Item no. 10041-5-9970 · ENU · Change 202174 · Approved 2018-12-28 · Page 5 / 9
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
