background image

Nova Flair GmbH & Co. KG, Operating Instructions with EU Declaration of Conformity Dust Extraction Unit Taifun II Premium GreenTech

8

INSTALLATION INSTRUCTIONS AND INSTRUCTIONS

 

FOR USE

Instruction Manual Taifun II Premium GreenTech

Function

The nail dust collector is switched on and off via the 

green push button.

The speed control is used for stepless adjustment of 
the power. of the power.

Cleaning

Use the hand screws (knurled screws) to loosen the 

removable front panel and carefully pull out the acti-

vated charcoal lamella filter slowly using a loop. 

For this purpose, it is best to use our additionally 

available dust collection tray. 

The activated charcoal lamella filters should be taken 

out and cleaned about 2 2-4 times per month. The 

remaining coarse dust is simply removed by pulling 

out the large dust collection tray (optionally available) 

and disposed of. If there is no dust collection tray, the 

dust must be sucked out from the inside through the 

large filter openings with a hoover and a narrow cre

-

vice nozzle attachment or similar.

Also clean or vacuum the lamella filter very carefully 

on the lower side only (not the clean air side at the 

top). Do not treat it wet and replace it after approx. 

one year.

The  replacement  of  the  filters  and  the  frequency  of 

cleaning can vary depending on the effort, care and 

customer volume.

1.  Carefully unpack the nail dust collector 

and first check that the black rubber seals 

on the edges stick properly.

2.  Place the nail dust collector on the under-

side of the table top and adjust it so that 

the cut-out for the ventilation grille is as 

central as possible (see sketch).

3.  Use the jigsaw etc. to make a cut-out in 

the centre with a diameter of Ø 160 mm.

4. 

Now you can fix the nail dust collector with 

suitable screws. (not included in the deli-

very).

 

Please pay attention to the length of 

the screws!

If anything is unclear, please contact us via the communication channels known to you. It will then be explained 

to you again in detail.

Kaitstud / Secured by https://mereneid.eu/

Summary of Contents for NOVA FLAIR TAIFUN II Premium GreenTech













Reviews: