Operating instructions
K3G450-AZ30-01
Translation of the original operating instructions
3.2 Nominal data
Motor
M3G150-IF
Phase
3~
Nominal voltage / VAC
400
Nominal voltage
range / VAC
380 .. 480
Frequency / Hz
50/60
Type of data definition
ml
Speed (rpm) / min
-1
2750
Power input / W
5370
Current draw / A
8.3
Min. ambient
temperature / °C
-25
Max. ambient
temperature / °C
40
ml = Max. load · me = Max. efficiency · fa = Running at free air
cs = Customer specs · cu = Customer unit
Subject to alterations
3.3 Data in accordance with ecodesign regulation EU 327/
2011
Actual
Request 2015
01 Overall efficiency η
es
/ %
64.9
59.2
02 Measurement category
A
03 Efficiency category
Static
04 Efficiency grade N
67.7
62
05 Variable speed drive
Yes
06 Year of manufacture
The year of manufacture is specified on the
rating plate on the product.
07 Manufacturer
ebm-papst Mulfingen GmbH & Co. KG
County court Stuttgart · HRA 590344
D-74673 Mulfingen
08 Type
K3G450-AZ30-01
09 Power input P
ed
/ kW
5.37
09 Air flow q
v
/ m³/h
8040
09 Pressure increase total p
fs
/
Pa
1492
10 Speed (rpm) n / min
-1
2750
11 Specific ratio
*
1.02
12 Recycling/disposal
Information on recycling and disposal is
provided in the operating instructions.
13 Maintenance
Information on installation, operation and
maintenance is provided in the operating
instructions.
14 Additional components
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.
*
Specific ratio = 1 + p
fs
/ 100 000 Pa
Data definition with optimum efficiency. The indicated efficiency values for obtaining
conformity with the Ecodesign Directive EU 327/2011 were achieved with defined air
conduction components (e.g. inlet nozzles). The dimensions are to be requested from ebm-
papst. If other air guide geometries are used on the installation side, the ebm-papst
evaluation loses its validity/conformity must be confirmed again. The product does not fall
within the scope of Regulation (EU) 2019/1781 due to the exception specified in Article 2(2a)
(motors completely integrated into a product).
3.4 Technical features
Mass
54 kg
Size
450 mm
Motor size
150
Surface of rotor
Coated in black
Material of electronics
housing
Die-cast aluminium
Material of impeller
Aluminium sheet
Material of mounting
plate
Sheet steel, galvanised
Material of support
bracket
Steel, coated in black
Material of inlet nozzle
Sheet steel, galvanised
Number of blades
7
Direction of rotation
Clockwise, seen on rotor
Type of protection
IP55
Insulation class
"F"
Humidity (F) /
environmental
protection class (H)
H1
Mounting position
Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation
drainage holes
Rotor-side
Operation mode
S1
Motor bearing
Ball bearing
Technical features
- Output 10 VDC, max. 10 mA
- Output 20 VDC, max. 50 mA
- Output for slave 0-10 V
- Input for sensor 0-10 V or 4-20 mA
- External 24 V input (programming)
- External release input
- Alarm relay
- Integrated PID controller
- Motor current limit
- PFC, passive
- RS485 MODBUS RTU
- Soft start
-Maximum EEPROM write cycles
100,000
- Control input 0-10 VDC / PWM
- Control interface with SELV potential
safely disconnected from the mains
- Over-temperature protected
electronics / motor
- Line undervoltage / phase failure
detection
Touch current acc.
IEC 60990 (measuring
network Fig. 4, TN
system)
<= 3.5 mA
Electrical connection
Terminal box
Motor protection
Reverse polarity and locked-rotor
protection
Protection class
I (if protective earth is connected by
customer)
Product conforming
to standard
EN 61800-5-1; CE
Approval
CSA C22.2 no. 77 + CAN/CSA-
E60730-1; EAC; UL 1004-7 + 60730-1
Item no. 50864-5-9970 · ENG · Revision 209539 · Release 2021-02-12 · Page 5 / 15
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com