Operating instructions
G3G250-GN17-01
Translation of the original operating instructions
You can control the blower either via the 0-10 VDC input or the
PWM input. Note: Inputs cannot be used simultaneously.
3.2 Nominal data
Motor
M3G084-FA
Phase
1~
Nominal voltage / VAC
230
Nominal voltage
range / VAC
208 .. 240
Frequency / Hz
50/60
Type of data definition
ml
Speed / min
-1
4800
Power input / W
1150
Current draw / A
5.7
@ 208 V
Min. ambient
temperature / °C
-20
Max. ambient
temperature / °C
60
Min. temp. of flow
medium / °C
0
Max. temp. of flow
medium / °C
60
ml = max. load · me = max. efficiency · fa = running at free air
cs = customer specs · cu = customer unit
Subject to alterations
3.3 Data according to ErP directive
Installation category
A
Efficiency category
Static
Variable speed drive
Yes
Specific ratio
*
1.03
*
Specific ratio = 1 + p
fs
/ 100 000 Pa
Actual
Request
2013
Request
2015
Overall efficiency η
es
62.6
47.5
50.5
Efficiency grade N
73.1
58
61
Power input P
ed
/ kW
1.01
Air flow q
v
/ m³/h
875
Pressure increase total p
sf
/ Pa
2400
Speed n / min
-1
4935
Data established at point of optimum efficiency
3.4 Technical features
Mass
13.2 kg
Size
250 mm
Surface of rotor
Coated in black
Material of protective
cover
Polyflam RPP 374-ND CS1 (UL 97-V0)
Material of impeller
Aluminum sheet
Housing material
Die-cast aluminum
Number of blades
7
Direction of rotation
Clockwise, seen on rotor
Type of protection
IP 20
Insulation class
"B"
Mounting position
any
Condensate discharge
holes
Rotor-side
Operation mode
S1
Motor bearing
Ball bearing
Technical features
- Tach output
- Over-temperature protected
electronics / motor
- PFC, active
- Motor current limit
- Line undervoltage / phase failure
detection
- PWM control input
- Control input 0-10 V
Touch current acc.
IEC 60990 (measuring
network Fig. 4, TN
system)
<= 3.5 mA
Electrical leads
With plug
Motor protection
Locked-rotor protection
Protection class
I (if protective earth is connected by
customer)
Approval
CSA C22.2 Nr.113; UL 507; CCC
For cyclic speed loads, note that the rotating parts of the device
are designed for maximum one million load cycles. If you have
specific questions, contact ebm-papst for support.
3.5 Mounting data
For depth of screw, see chapter 3.1 Product drawing
;
Secure the mounting screws against accidentally coming loose (e.g.
by using self-locking screws).
You can obtain additional mounting data from the product drawing if
necessary.
3.6 Transport and storage conditions
;
Use the device in accordance with its protection type.
Max. permissible
ambient motor temp.
(transp./ storage)
+80 °C
Min. permissible
ambient motor temp.
(transp./storage)
-40 °C
3.7 Electromagnetic compatibility
EMC interference
immunity
Acc. to EN 61000-6-2 (industrial
environment)
EMC harmonics
Acc. to EN 61000-3-2/3
EMC interference
emission
Acc. to EN 61000-6-4 (industrial
environment)
Item no. 50133-5-9970 · Revision 67913 · Release 2009-10-14 · Page 6 / 12
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com