Operating instructions
D4D250-BA02-01
Translation of the original operating instructions
3.2 Nominal data
Motor
M4D094-LA
Phase
3~
3~
Nominal voltage / VAC
400
400
Wiring
Y
Y
Frequency / Hz
50
60
Method of obtaining
data
fa
ml
Valid for approval/
standard
CE
CE
Speed (rpm) / min
-1
1240
1410
Power consumption / W
1140
1210
Current draw / A
2.1
2.2
Min. back pressure / Pa
0
250
Min. ambient
temperature / °C
-40
-40
Max. ambient
temperature / °C
60
45
Starting current / A
4.6
4
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
Actual
Req. 2015
01 Overall efficiency η
es
/ %
40.4
35.9
02 Measurement category
A
03 Efficiency category
Static
04 Efficiency grade N
48.5
44
05 Variable speed drive
No
06 Year of manufacture
The year of manufacture is specified on the
product's rating label.
07 Manufacturer
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart
· HRA 590344
D-74673 Mulfingen
08 Type
D4D250-BA02-01
09 Power consumption P
e
/ kW
0.52
09 Air flow q
v
/ m³/h
2005
09 Pressure increase total p
sf
/
Pa
381
10 Speed (rpm) n / min
-1
1405
11 Specific ratio
*
1.00
12 Recycling/disposal
Information on recycling and disposal is
provided in the operating instructions.
13 Maintenance
Information on installation, operation and
maintenance is provided in the operating
instructions.
14 Additional components
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.
*
Specific ratio = 1 + p
fs
/ 100 000 Pa
Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller
combination in a standardized measurement setup.
3.4 Technical description
Weight
17.3 kg
Size
250 mm
Motor size
94
Impeller material
Sendzimir galvanized sheet steel
Housing material
Sendzimir galvanized sheet steel
Direction of rotation
Clockwise, viewed toward rotor
Degree of protection
IP20
Insulation class
"F"
Moisture (F) /
Environmental (H)
protection class
H0 - dry environment
Installation position
Any
Mode
Continuous operation (S1)
Motor bearing
Ball bearing
Touch current
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
< 0.75 mA
Motor protection
Thermal overload protector (TOP) with
basic insulation
with cable
Axial
Protection class
I (with customer connection of protective
earth)
Conformity with
standards
EN 60034-1 (2010); CE
Approval
CCC; EAC
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
;
Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.
3.5 Mounting data
For screw clearance, see Chapter 3.1 Product drawing
;
Secure the screws against unintentional loosening (e.g. use self-
locking screws).
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
Item no. 12006-5-9970 · ENU · Change 213948 · Approved 2020-03-25 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
