EBA 721 LT Operating Instructions Manual Download Page 22

Page: 22 / 24

- 22 -

EBA 721 LT

6. Technical data

Sound level DIN 45635-27:

max. 73 dB(A)

Minimum space requirement B x T:
without side tables

130 cm x 151 cm

with side tables

210 cm x 160 cm

Clamping pressure

250 dN bis 2000 dN

Weight without side tables:

584 kg

Weight with side tables:

620 kg

Capacity of hydraulic oil
Shell Tellus C32 or similar

1,5 l

Used oil must be disposed of at the
authorized place.

The exact technical specifications can be found on
the technical specifications sticker on the machine.

Safety light beam

Total reaction time of safety device:

95 ms

Resolution top

20 mm; 30 mm

Resolution front

40 mm

Distance:

238 mm; 20 mm

Distance:

318 mm; 30 mm

Distance:

460 mm; 40 mm

7. Accessories

Attention!

Only use accessories recommended by the

manufacturer.
Not all of the accessories illustrated or
described are included as standard delivery.

Knocking-up block (6)

9000 521

Blade change set (31)

9000 514

HSS - Blade (42)

9000 141

6 Cutting sticks (26)

9000 039

Side tables left and right

9000 550

Grease gun (44)

9004 683

Summary of Contents for 721 LT

























Search results

Summary of Contents for 721 LT

Reviews:

Related manuals for 721 LT

Brands by name

Popular brands

EBA 721 LT, Operating Instructions Manual

Search results

Summary of Contents for 721 LT

Reviews:

Related manuals for 721 LT

Brands by name

Popular brands