EBA 430 E, Operating Instructions Manual

Page: 24 / 46

EBA 430 E • EBA 430 EP
-25-
cm
inch
-24-
cm
inch
Programming
only EBA 430 EP
This control system enables you to store 9
programs with 9 programmable steps. One step
represents one measurement. After entering
the program numbers you are able to change
between several program steps with the button
r
and
h.
First figure in display = program number,
Second figure = program step.
Dimensions below 9 cm can only be
approached with the
S
button held pressed.
„
u
“ on the Display
➞
the entered dimension is
too low. (Smallest measurement 3,5 cm).
„
o
“ on the Display
➞
the entered dimension is
too high. (Largest measurement 38,5 cm).
Each program step corresponds to one
dimension. The indicated program step can be
overwritten at any time. These programs remain
stored when the machine is off. Should you
change to another dimension unit all
programmed measures are converted into the
new unit (cm and inch).
Entering a program
•
Press
p
➞
P
appears in the Display.
•
1
...
9
Enter program number 1...9.
(First figure in Display = program number).
•
Enter dimension, or move the backgauge to
the desired measurement with the rotary
control.
•
g
Store the dimension
➞
next program step
appears.
•
Enter the next dimension.
(should an ejection be desired before this
cut push the
z
button, measurement and
eject function are stored now).
•
g
Store the dimension.
•
Should the entered program be required
immediately
➞
Press
S
(program is closed).
Press
S
again (backgauge moves to the
dimension of the 1st program).
Or:
•
p
+
s
Escape the program mode.
•
The eject function must be programmed in
the 1 st dimension if the paper stack should
be ejected at the end of a program where
several cutting processes are made.
Eject function
•
Set the measurements
➞
push the
z
button.
•
g
Store the dimension.
Backgauge moves in the program for
unloading paper to the front and then to the
measurement which has been set in the
panel.
Cancel a program
•
p
Press
➞
P
appears in the display..
•
1
...
9
Enter program number 1 ... 9.
•
Press
c
twice.
Each program has to be cancelled separately.
Single program steps can only be overwritten.
Deleting the last program step
•
Press
0
.
•
Press
g
.
p
+
s
Escape the program mode.
Working with programs
• Press
p
➞
P
appears on the display
•
1
...
9
Enter Program number 1 ... 9
With the button
r
and
h
you are able to change
between several program steps.
With
S
the backgauge moves to the indicated
dimension.
With
s
the backgauge stops.
General
LED "S" blinks
➞
the basic position will appear.
LED "S" is off
➞
the actual dimension appears.
In the program mode the ejection of paper
z
is
not possible. The ejection of the paper has to
be programmed.
After each cut pressing the button
S
the
backgauge moves to the next dimension.
Escape the program mode
•
Press
p
➞
P
appears on the display.
•
Press
s
➞
Escape the program mode.
Program buttons
h
and
r
programms
By means of buttons
h
and
r
dimension of your
choice can be reached.
(Basic adjustment
h
= 38,5 cm,
r
= 9 cm).
•
p
and simultaneously
h
resp.
r
➞
(
h U
resp.
r D
appears on the display.
•
Insert the desired dimension.
•
g
Store dimension.
Display in cm or inch
•
Press
i
➞
Display changes between cm
and inch. (See picture left).
Adjust the eject-dimension
The eject dimension is programmed to
29,50 cm. It may be changed as follows:
•
Press
p
Press
p
+
z
➞
e
on Display.
•
Insert the desired dimension.
•
g
Store dimension.