background image

14

 – VRS12 and VRS18

VRS12 and VRS18 – 

15

9. WARRANTY

Warranty: 

LOUD Technologies Inc. requires its authorized EAW Commercial distributors 

abide by the following warranty terms for all EAW Commercial brand products (all dates 

are from the date of delivery from an Authorized EAW Commercial Distributor to the end 

user/installation site):

      Loudspeakers – 5 years; Active Electronics – 5 years; Accessories – 2 years.

What Is Covered:

 Defects in workmanship and materials and against malfunctions. EAW 

Commercial distributors must remedy all such defects and malfunctions without charge 

for parts or labor if the warranty applies. Final determination of warranty coverage lies 

solely with each authorized EAW Commercial distributor.

What Is Not Covered:

 This warranty does not extend to damage or malfunctions 

resulting from, but not limited to, shipment, improper installation, misuse, neglect, 

abuse, normal wear, accident, or to any product on which the serial number has been 

modified or removed. Exterior defects in or damage to the exterior appearance are 

specifically excluded from this warranty. EAW Commercial distributors shall not be liable 

for incidental or consequential damages resulting from the use of EAW Commercial 

products. Repairs and/or modifications by other than an Authorized EAW Commercial 

Distributor automatically voids this warranty.

Summary of Contents for VRS12 VRS18

















Reviews: