Eaton VORAD AlwaysAlert Installation Manual Download Page 19 | Manualshive

Page: 19 / 30

background image

16

Component Installation

Wiring Harness

Installation

Wiring Harness Installation

Installation of the wiring harness should start from the CPU and then extend outward to the other components.

Avoid routing the wiring harness near sharp edges or extreme heat, which could damage wire insulation.

Route the wires along existing wires, up through existing pass-through holes or spaces in the floor or dashboard to the
installed components. Coil up the slack in the wire harness and store it neatly behind the dashboard or kick panels,
depending upon the location of the CPU. The following illustration shows a typical installation of the wiring harness.

Note: Use the protective loom where necessary. Tie-wrap the harness for a secure/neat installation.

1 - Driver display unit
2 - Side sensor display
3 - To side sensor and antenna assembly

4 - Central Processing Unit
5 - Ground strap

CAUTION

2

1

3

4

5

«
...
17
18
19
20
21
...
»

Summary of Contents for VORAD AlwaysAlert































Reviews:

No comments

Related manuals for VORAD AlwaysAlert

Brand: QUIETON Pages: 24

Brand: Quest Engineering Pages: 24

Brand: Nauticam Pages: 2

Brand: Baicells Pages: 32

Brand: BAFANG Pages: 18

Brand: VANPOWERS Pages: 23

Brand: Barco Pages: 2

Brand: Zipp Pages: 39

Brand: HAI Pages: 2

AERASGARD RCO2-W

Brand: S+S Regeltechnik Pages: 32

Brand: S-BOL Pages: 3

QuadraTop Adventure Top S

Brand: Quadratec Pages: 20

Brand: GBRacing Pages: 2

Brand: Pout Pages: 5

Brand: Subaru Pages: 3

Brand: Heitronic Pages: 12

Brand: LSL Pages: 4

Brand: MSA Pages: 163

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands