background image

 
 

UPS 450 - 550 kVA (2x225 - 2x275 kVA)  

User’s and Installation Guide 

1027574 

Revision B

40

Installation checklist

  All packing materials and restraints have been removed from each cabinet.

r

   Each cabinet in the UPS system is placed in its installed location.

r

   A cabinet grounding/mounting kit is installed between any cabinets that are bolted 

together.

r

   All conduits and cables are properly routed to the UPS and any ancillary cabinets.

r

   All power cables are properly sized and terminated.

r

   Neutral conductors are installed or bonded to ground as per requirements.

r

  Battery cables are terminated on E4 (+) and E5 (–).

r

   Battery Shunt trip and Aux contact signal wiring is connected from the UPS to the battery 

breaker.

r

   LAN and telephone drops are installed.

r

   All telephone and LAN connections have been completed.

r

   A ground conductor is properly installed.

r

   Air conditioning equipment is installed and operating correctly.

r

   The area around the installed UPS system is clean and dust-free. (It is recommended that 

the UPS be installed on a level floor suitable for computer or electronic equipment.)

r

   Adequate workspace exists around the UPS and other cabinets.

r

   Adequate lighting is provided around all UPS equipment.

r

   A 230 Vac service outlet is located within 7.5 meters of the UPS equipment.

r

   The Remote Emergency Power-off (REPO) device is mounted in its installed location and its 

wiring is terminated inside the UPS cabinet.

r

   The normally-closed (NC) Emergency Power-off contact (pins 1 and 2 on TB1) is jumpered if 

not used.

r

   Alarm relays and building alarms are wired appropriately. (OPTIONAL)

r

   A remote battery disconnect control is mounted in its installed location and its wiring is 

terminated inside the UPS and battery cabinet. (OPTIONAL)

r

   Accessories are mounted in installed locations and wiring is terminated inside the UPS 

cabinet. (OPTIONAL)

r

   The debris shield covering the UPS cabinet ventilation grill is removed.

r

  Startup and operational checks are performed by an authorized Eaton Customer Service 

Engineer.

Summary of Contents for UPS 225275 kVA Powerware 9395













































































Reviews: