OPERATION
The Sure-Lites Eagle Eye Self Diagnostics is continuously
monitoring your emergency
fi
xture, and will signal any
failure through the 3 color indicator LED.
INITIAL OPERATION
When the unit is
fi
rst powered up, it will go into a 24 hour
fast charge, indicated by the indicator LED pulsing green.
Once the unit has fully charged, it will perform a self calibration,
after which the LED will change to steady green,
indicating the unit is fully charged and
fl
oat charging the
battery to maintain readiness.
AUTOMATIC TESTING
The unit will perform a battery capacity, lamp/LED, and
charge circuit test every 30 days for 30 seconds. During
this time, the indicator LED will change to a steady yellow.
It will perform a full battery capacity (90 minute) test once
per year. During this time, the indicator LED will change to
a blinking yellow.
MANUAL TESTING
•
10 Second “Installation” test – Press and release the
test button once during fast charge (blinking green) to
initiate a 10 second quick test. The sign will switch to
emergency mode for 10 seconds allowing the installer
to verify proper installation of the unit, and the LED
indicator will turn solid yellow.
•
30 Second Test - Press and release the test button once
during
fl
oat charge (steady green). The indicator LED will
turn steady yellow to indicate the unit is performing a 30
second test of the batteries and lamps/LEDs.
•
90 Minute Test - Press and release the test button a
second time during a 30 second test (steady yellow) to
change to a 90 minute test. During this test, the LED indi-
cator will change to blinking yellow, and the circuit will per-
form a full battery capacity, charge circuit, and LED test.
•
Cancelling Test – Press and release the test button
during the 90 minute test (
fl
ashing yellow) to return the
fi
xture to its original state (fast charge or
fl
oat charge).
LASER TEST
The SELDWTA29SD/SELDWA50SD/ATLELDWTA100SD/
ATLELDWA300SD series is equipped with a Laser Test
function, that allows the unit to be manually tested without
the need to physically press the test button. Shining a laser
pointer in the hole marked “LASER TEST” on the bottom of
the unit has the same effect as a press and release of the
test button.
CLEARING FAILURE CODES
•
A battery failure (LED two blink red) can be cleared by
replacing the battery. Disconnecting the battery and AC
power, or performing a full 90 minute discharge, will reset
the error code, however, it will return if the battery is faulty.
•
Charge Circuit (LED three blink red) and lamp/LED failure
(LED four blink red) will clear when the unit successfully
passes a manual or automatic 30 second test.
INDICATORS
LED Off - No power to unit, emergency mode.
LED Steady Green - Unit is fully charged and is
fl
oat charging
the battery to maintain readiness.
LED Green Pulse - Unit is in a 24 hour fast charge of the bat-
tery.
LED Two Blink Red - Battery has failed a capacity test, or the
battery is disconnected. See “Clearing Failure Codes” above.
LED Three Blink Red - Battery charge circuit has failed. See
“Clearing Failure Codes” above.
LED Four Blink Red - Lamps have burned out, or on an EXIT/
Combo, 50% or more of the LEDs have failed. See “Clearing
Failure Codes” above.
LED Steady Yellow - 30 second test or 10 second quick test
(Fast Charge only).
LED Blinking Yellow - 90 minute test
MAINTENANCE
None required. Replace the batteries as needed according
to ambient conditions. Equipment should be tested every
30 days in accordance with local codes.
NOTE: Servicing of any parts should be performed by quali
fi
ed personnel. Only use replacement parts supplied by Eaton
Lighting. Use of unauthorized parts may void the warranty.
CAUTION: This equipment is furnished with a sophisticated
low voltage battery disconnect to protect the battery
from over discharge after its useful output has been used.
Allow 24 hours recharge time after installation or power
failure prior to 90 minute testing.
TROUBLE SHOOTING GUIDE
1. If LED heads or charge indicator LED does not illuminate,
check the following:
2. Check AC supply – verify that unit has 24 hour AC supply.
3. Unit is shorted or battery is not connected.
4. Battery discharged. Permit unit to charge for 24 hours and
then re-test.
5. If following the above trouble shooting hints does not solve
your problem, contact your local Eaton Lighting represen-
tative for assistance
