background image

2

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2

Section 1

Installation Checklist

1.

Verify that the following items are available:

o

Power Xpert Gateway Minislot (PXGMS) UPS Card package contents 
(card, cable, Quick Start Instructions)

o

Phillips

®

 screwdriver

o

Available USB port on a computer running Microsoft

®

 Windows

®

o

Web browser (Microsoft Internet Explorer

® 

version 8.0 and higher, 

Mozilla

®

 Firefox

®

, or Google Chrome™ are recommended)

2.

If you are going to use Dynamic Host Configuration Protocol (DHCP), provide 
your local network administrator with the card's MAC address. The MAC 
address is located on either the shipping box label or the label on this card.

o

MAC Address

_____________________________________________

3.

If you are not going to use DHCP to provide any of the settings listed below, 
contact your local network administrator for the settings. 

In the table below, check the 

DHCP

 check box or enter the values for manual 

configuration.You will reference this data later in the procedure.

4.

If you need e-mail functionality, obtain the SMTP mail server's IP address or 
host name. If using the SMTP host name, verify that you also have the 
Name Server IP address (see Step 3).

o

SMTP (mail server) IP Address
or Host Name

_____________________________________________

Item

DHCP*

Manual Configuration

IPv4

o

Card IP Address:

________________________

Netmask:

________________________

Gateway:

________________________

DNS – Name Servers

o

Name Server #1:

________________________

Name Server #2:

________________________

Name Server #3:

________________________

DNS – Domain

o

Domain:

________________________

* The network administrator normally sets up the DHCP server to provide a static IP address each time 
the card makes a DHCP request.

Summary of Contents for PXGMS Power Xpert Gateway Minislot UPS



























Reviews: