manualshive.com logo in svg

Eaton Power Xpert Gateway Minislot, Quick Start Instructions

Share
Download
Eaton Power Xpert Gateway Minislot Quick Start Instructions Download Page 17

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 06

13

–

Administrator name: admin

–

Password: 00E0D8FFC0C4

•

For firmware versions older than 2.6.5 the default username and password is “admin”.

When the PXGMS card Web page displays, you know the fixed IP Address is working.

NOTE

For detailed information, refer to the

Eaton Power Xpert Gateway Minislot PXGMS UPS Card User’s Guide

.

EEnnaabbllee B

Brroow

wsseerr C

Coom

mppaattiibbiilliittyy M

Mooddee

Browser compatibility allows Web pages designed for older versions to display properly. If data does not
display properly on your PXGMS card Web page, the browser compatibility mode should be enabled.

To enable the compatibility mode:

1.

Open your Web browser.

2.

In the Menu bar select

Tools > Compatibility View Settings

. The

Compatibility View Settings

window

displays (see

Figure 12

).

Figure 12. Compatibility View Settings Window

3.

Under “Add this website:” type the IP address of the PXGMS card and click

Add

.

NOTE

Close and re-open your browser so that the changes take effect.

Enable Browser Compatibility Mode

Summary of Contents for Power Xpert Gateway Minislot



























Reviews:

No comments

Brands by name

Popular brands

Load more brands