Eaton Matrix Telecom Inverter System Installation And Operation Manual Download Page 53

Page: 53 / 86

Maintenance

IPN 997-00012-68D February 2010

Fast Flash (2Hz)

STS is in Inverter Bypass
mode (this refers to the
internal mode of STS, not the
position of the MBS).

Solid

Mains or inverter abnormal

Fast Flash (2Hz)

If the status of green and
yellow LED is the same, then
STS is in Inverter Bypass
mode, otherwise the Back-
feed relay is open.

Yellow

Fastest Flash
(5Hz)

STS Output is abnormal

Slow Flash (1Hz)

Fan lock, CAN
communication fail, or
EEPROM fault

Fast Flash (2Hz)

SCR short or auxiliary power
supply fault

Fastest Flash
(5Hz)

MBS position abnormal.

Red

Solid

STS Fault mode, may be
overload, over temperature,
or output short.

Note: If more than one warning exists at the same time, then the LED will display the highest
priority.

Summary of Contents for Matrix Telecom Inverter System















































































Search results

Summary of Contents for Matrix Telecom Inverter System

Reviews:

Related manuals for Matrix Telecom Inverter System

Brands by name

Popular brands

Eaton Matrix Telecom Inverter System, Installation And Operation Manual

Search results

Summary of Contents for Matrix Telecom Inverter System

Reviews:

Related manuals for Matrix Telecom Inverter System

Brands by name

Popular brands