Eaton Magnum MR2 Instructions For Installation, Operation And Maintenance Download Page 10

Page: 10 / 12

Instructional Booklet

IB013003EN

Effective June 2023

Instructions for installation, operation,

and maintenance of Magnum MR2

(integral racking)

EATON

www.eaton.com

Appendix

Circuit breakers equipped with MR2 have a thin layer of Magnalube

applied to the primary disconnects, which is shown below (See

Figure 26) . If Magnalube is not present, please contact Eaton

Technical Support and order with style # shown in Table 3 .

Magnalube can be added to the leading edges and surfaces on all

primary disconnects that make contact with the cassette stabs .

Table 3. Greases used on Magnum PXR and PD-SB

Grease type

Desription

Magnalube

-G

Eaton standards

#53701AI

Color

Green

Manufactured by

Saunders Enterprises inc.

11-51 44th Road, Long Island City, New York 11101

Phone (718) 729-2690

www.magnalube.com

Figure 26. Magnalube applied to the primary disconnects.

Summary of Contents for Magnum MR2













Search results

Summary of Contents for Magnum MR2

Reviews:

Related manuals for Magnum MR2

Brands by name

Popular brands

Eaton Magnum MR2, Instructions For Installation, Operation And Maintenance

Search results

Summary of Contents for Magnum MR2

Reviews:

Related manuals for Magnum MR2

Brands by name

Popular brands