background image

7

MERCURY SWITCH TO MICROSWITCH RETROFIT KIT KA349WE INSTALLATION INSTRUCTIONS

  MN280022EN   October 2015

5.  Route switch SW2 cable along frame wall and pull it 

through the cable exit hole to terminal block (Figures 4 

and 10). Do not attach cable leads to terminal block at 

this time.

6.  Use the previously removed hardware and plastic cable 

retainers to secure cable to frame (Figures 10 and 16).

Figure 15.  Plastic cable retainer assembly.

Completing switch SW2 assembly

Matching original orientation, reinstall parts removed.
1.  Reinstall pin, spacers, and two, small lower springs 

(Figure 17). (Vacuum unit without spacers shown. 

Oilinterrupting units have two spacers. )

otee:

N

If no tool is available to grab springs, place a piece 

of strong string through spring’s connecting loop and 

pull spring into place. Once spring is connected, pull 

string clear.

Figure 16.  Reinstall springs and retaining pins.

2.  Reinstall retaining pin, new C rings (Item 22), and small 

upper spring.

3.  Slide spring retaining pin through the two large springs, 

spacers, and new C rings (Item 21). Tighten C rings.

4.  With H bracket disengaged, gently push down on 

switch SW2 until hearing a click as switch contact 

encounters cam and closes (Figure 18).

Figure 17.  Side view, switch SW2 assembled to 

mounting plate.

5.  Hold switch in place where click is heard and tighten 

retaining hardware. Take care not to over tighten and 

damage switch.

6.  Recheck all work. Engage and disengage the H bracket 

using the following directions:

A. Turn the handle shaft clockwise with a pair of pliers 

to engage and latch the H bracket.

B. Turn the handle shaft counterclockwise with a pair of 

pliers to disengage the H bracket.

Make sure mechanism does not encounter interference 

during movement. Adjust spacers as needed to eliminate 

any interference.

Gently push down for 

final switch adjustment

Approximate placement of 

microswitch Stop Nuts: Torque to 

13-15 in-lbs after adjustment

Cable Pass Through

Mounting holes, plate to frame

Two large springs attached to spring 

retaining pin

Spring retaining pin

Upper small spring, 

attach here

Spacers

Pin

Handle shaft

H bracket

Lower two small springs, attach here

Summary of Contents for KA349WE

















Reviews: