![background image](http://html1.mh-extra.com/html/eaton/iq-250/iq-250_quick-start-manual_3831340002.webp)
IQ 250/260 Transducer
www.eaton.com
IB02601005E
Q-2
Program the IQ 250/260T Using RS-485
Q
Communication Wiring
The IQ 250/260T’s RS-485 port uses standard 2-wire, Half Duplex Architecture.
Connect to Master and Slave devices as shown (+ to +, - to -).
Q
Factory Initial Default Settings
When the IQ 250/260T is powered up, for 10 seconds you can connect to the meter
using the Factory Default Settings (even if the Device Profile has been changed). After
10 seconds the Device Profile reverts to the actual Device Profile in use. This is one
way you can always connect to the meter. The Factory Initial Default Settings are:
Device Address
: 1
Baud Rate
: 9600
Protocol
:
Modbus RTU
Q
Connection Steps
1.
Open IQ 250/260 Configuration Software.
2. Click
Connect
on the Tool Bar. The Connect screen opens. Make sure your
settings match those shown on the right.
3. Click
Connect
. The Device Status screen confirms the connection.
4. Click
OK
. The main screen opens.
Q
Configuration Steps
5. Click
the
Profile
button on the Tool Bar. The Device Profile screen
opens, showing the CT, PT Ratios
and
System Hookup (
Scaling
)
fields.
6. Configure
Scaling
settings
based on your application.
7. Click
Communications
and select settings based on your application.
Q
Scaling (CT, PT Ratios and System Wiring)
CT
Numerator, Denominator, Multiplier, CT Fullscale (Calculated automatically)
PT
Numerator, Denominator, Multiplier, PT Fullscale (Calculated automatically)
System Wiring
: Use pull-down menu to select.
Number of Phases
: One, Two or Three
NOTE:
Voltage Full Scale = PT Numerator x PT Multiplier
Current Full Scale = CT Numerator x CT Multiplier
IMPORTANT
! Specify Primary and Secondary Voltage in Full Scale (NOT
Ratios).
Example CT Settings:
200/5 Amps:
Set the Ct-n value for 200, Ct-S value for 1.
800/5 Amps:
Set the Ct-n value for 800, Ct-S value for 1.
2,000/5 Amps:
Set the Ct-n value for 2000, Ct-S value for 1.
10,000/5 Amps:
Set the Ct-n value for 1000, Ct-S value for 10.
Example PT Settings:
14,400/120 Volts: Pt-n value is 1440, Pt-d value is 120, Pt-S value is 10.
138,000/69 Volts: Pt-n value is 1380, Pt-d value is 69, Pt-S value is 100.
345,000/115 Volts: Pt-n value is 3450, Pt-d value is 115, Pt-S value is 100.
345,000/69 Volts Pt-n value is 345, Pt-d value is 69, Pt-S value is 1000.
Q
Communications Settings
COM2
(RS-485):
Address
(1-247)
Protocol
(Modbus RTU, ASCII or DNP)
Baud Rate
(9600 to 57600)
Response Delay
(0-750 msec)
Q
Update Device
8.
When settings are complete, click the
Update Device
button to send a new profile to the IQ 250/260T.
9. Click
Exit
or click other tabs to update additional screens.
10.
Use IQ 250/260 Configuration Software to communicate with the device and perform required
tasks.
NOTE: For further details and additional programming screens, see the IQ 250/260 Manual on the enclosed CD.