Questions?/Des questions?/ ¿Preguntas? 1-800-334-6871 [email protected]
1
Instruction Manual/Manuel d’instructions/Instrucciones
PACKAGING CONTENTS / CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE
MOUNTING YOUR FIXTURE
NOTE:
Do not mount within 2 feet of a highly reflective
exterior inside corner (Fig. 1).
1.
Turn off the power at the main fuse/breaker box.
2.
Attach mounting bracket (B) to junction box with
two screws (C) provided (Fig. 2).
3.
Screw the threaded mounting rod (D) into the
center of the mounting bracket (B) until the
threads are showing on the back side of the
mounting bracket (B) (Fig. 3).
WIRING YOUR FIXTURE
1.
Turn off the power at the main fuse/breaker box.
2.
Connect the black fixture wire to the black supply
wire (hot) using wire connector (E) (Fig. 4).
3.
Connect the white fixture wire to the white supply
wire (neutral) using wire connector (E) (Fig. 4).
4.
Connect the copper ground fixture wire to an
appropriate supply ground or a grounded
junction box.
NOTE:
Be careful to connect the wires correctly.
Make sure no bare strands of wire extend from the
wire connector (E) provided or other approved wire
connectors (not provided).
5.
Attach fixture to the threaded mounting rod (D).
6.
Secure with cap nut (F) (Fig. 5).
7.
Add silicone caulk around fixture to help maintain a
weather-resistant seal.
IITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Weatherproof silicone caulk
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Your fixture is prewired and preassembled for easy installation.
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Fixture designed for wall mount to a recessed junction box only. Install fixture to
junction box marked for use in wet locations.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation. Under Part 15 of the FCC Rules, any changes or modifications to
the fixture described in this instruction sheet that are not expressly approved by Eaton
could void the user’s authority to operate the equipment.
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
• Install patio light 7-10 feet above the ground.
• Do not mount fixture close to reflective surfaces such as windows, white walls, white
surfaces and water.
• When installing two fixtures on one switch, make sure the switch is rated for at least
a 1 A inductive load.
FE1450LPC
(Bronze/Bronze/
Bronce)
FE1435LPC
(Bronze/Bronze/
Bronce)
A.
Light fixture
Appareil d’éclairage
Accesorio
ENGLISH
C.
(2) #6 and (2) #8 junction box screws
(use the size that fits your junction box)
(2) Vis nº 6 et 2 vis nº 8 pour boîtier de
jonction (choisissez la dimension convenant
à votre boîtier de jonction)
(2) Tornillos #6 y (2) tornillos #8 para
montaje de la caja de conexión
(utilice el tamaño que mejor se
adecue a su caja de conexión)
E.
(3) Wire nuts
(3) Capuchons de connexion
(3) Conectores
de cable
WARNING
B.
Mounting bracket
Support de montage
Soporte de montaje
D.
Threaded mounting rod
Tige de fixation filetée
Varilla roscada para
montaje
F.
Cap nut
Écrou borgne
Tuerca tapa
2 ft.
2 ft.
2 ft.
1
2
Junction box
C
C
B
3
Junction box
D
B
5
Junction box
D
F
A
4
Junction box
D
E
E
A
