background image

91

Output Sleeve, Yoke and 4x4

Transmission Differences

3

FSO-2405

2nd Ed. 02/07

Rear Section

FSO-2405/142

FSO-2405/143

1

FSO-2405/144

1

2

3

4

5

6

7

Transmission with Output Sleeve
(used in this manual)

With the exception of some rear section parts, the
remaining transmission configuration is the same
for all other models.

4x4 Transmission

This transmission model has a shorter mainshaft
and there is neither the speedmoter sensor nor
the rotor, whose functions are not performed by
the transmission itself.

The rear housing is shorter and has a mounting
surface with holes for attaching a transfer box
(4x4).

1- Companion flange for attaching the transfer

box

Transmission with Universal Joint Yoke

This transmission model has an output yoke at the mainshaft end for coupling the drive shaft.

Both the speedometer sensor and rotor might or not be provided, depending on the vehicle
equiped with this transmission.

1- Snap ring
2- Thrust washer

3- Retaining ring
4- Rubber washer

5- Universal joint yoke
6- Rubber washer

7- Nut

Summary of Contents for Fuller FSO 2405 K




































































































































































Reviews: