Eaton Fuller FSO 2405 K Service Manual Download

Page: 128 / 163

128

Front Section Disassembly

Front Section

2nd Ed. 02/07

FSO-2405

FSO-2405/49

2mm

FSO-2405/48

Expansive Plugs

Installation

WARNING! Allways replace the removed
plug to prevent leaks.

1. With a clean rag and solvent, clean the plug

hole and remove any remaining sealant
compound. Do not use sand paper.

2. Apply sealant to the new plug and insert it into

the hole using the hands to guide the plug.

NOTE: Apply

Eaton E677

to plugs.

3. Use the proper tool and a hammer to force the

plug into the plug bore. The proper depth is
when the plug is 2 mm below the plug bore
top.

NOTE: See “Special Tools”, Ref. E001020.

FSO-2405/170

Summary of Contents for Fuller FSO 2405 K




































































































































































Search results

Summary of Contents for Fuller FSO 2405 K

Reviews:

Related manuals for Fuller FSO 2405 K

Brands by name

Popular brands

Eaton Fuller FSO 2405 K, Service Manual

Search results

Summary of Contents for Fuller FSO 2405 K

Reviews:

Related manuals for Fuller FSO 2405 K

Brands by name

Popular brands