Responding Time
Adjustable 0~20ms, Default10ms, selected through D1020)
AC Input Point Electrical Specification
Rated Input Voltage
100 to 120 VAC (-15%~+10%)
Maximum Input Current
Less than 20 mA
Minimum ON Voltage
80 VAC
Maximum OFF Voltage
30 VAC
Output Point Electrical Specification
Output Type
Relay-R
Transistor-T
Current
Specification
1.5A/1 point (5A/COM)
0.3A/1 point @ 40
; When the output of Y0 and Y1 is high-speed
pulse, Y0 and Y1 = 30mA
к
Voltage
Specification
Below 250VAC,
30VDC
30VDC
Maximum Loading
75VA (Inductive)
9W/1 point
When the output of Y0 and Y1 is high-speed pulse,
Y0 and Y1 = 0.9W (Y0 = 32kHz, Y1 = 10kHz), Y0
can be 50Khz using D registers
90 W (Resistive)
Responding Time
About 10 ms
Off
On 20us
Ш
Ш
On
Off 30us
Y0 and Y1 are specified points for high-speed pulse
4
MODEL NAME & I/O CONFIGURATION
Model
Input / Output
Profile
Reference
I/O Configuration
Power
Input Unit
Output Unit
Point
Type
Point
Type
ELC-PC12NNAR
24VDC
8 100~120VAC 4
Relay
S/S
X0
X1
X2
X3
X4
X5
X6
X7
C0
Y0
C1
Y1
C2
Y2
Y3
COM
X0
X1
X2
X3
X4
X5
X6
X7
C0
Y0
C1
Y1
C2
Y2
Y3
DC
AC
input
input
ELC-PC12NNDR 8
DC Sink or
Source
4 Relay
ELC-PC12NNDT
8
4 Transistor
5
INSTALLATION & WIRING
5.1 Installation of the DIN rail
The ELC can be secured to a cabinet by using the DIN rail that is 35mm high with a depth of 7.5mm. When
mounting the ELC on the DIN rail, be sure to use the end bracket to stop any side-to-side motion of the ELC, thus
to reduce the chance of the wires being pulled loose. At the bottom of the ELC is a small retaining clip.
To remove it, pull down the retaining clip and gently pull the ELC
away from the DIN rail. As shown on the right:
When installing the ELC, make sure that it is installed in an
enclosure with sufficient space (as shown on the right) to its
surroundings so as to allow heat dissipation.
D
D
D
D
E
L
C
D>50mm
5.2 Wiring
22-16AWG
<1.5mm
1.
Please use 22-16AWG (1.5mm) wiring (either single or multiple core) for
I/O wiring terminals. The specification for the terminals is as shown on the
left. ELC terminal screws should be tightened to 1.95 kg-cm (1.7 lb-in). Use
Copper Conductor Only, 60/75 °C.
2.
I/O signal wires or power supply should not run through the same
multi-wire cable or conduit.
5.3 Power Input Wiring
1. When DC voltage is supplied to the ELC, make sure the power is at terminals 24VDC and 0V (power range is
20.4VDC~28.8VDC). When voltage is lower than 20.4VDC, ELC will stop operating, all outputs will turn OFF
and the ERROR LED will flash continuously.
2. If the power-cut time is less than 10ms, the ELC still operates unaffectedly. If the power-cut time is too long or
the power voltage drops, the ELC will stop operating and all the outputs will be Off.
DC Input Type
2A
20.4V~28.8V
DC/DC
+5V
S/S
X0
X1
X2
24V
0V
GND
ELC
5.4 Input Point Wiring
