background image

3

Instruction Leaflet 

Installation    Instructions  For EG-DC  Circuit     Breaker

and Molded Case Switch

EATON  CORPORATION www.eaton.com

Figure 3. Load Isolated from Power Source. Grounded or 

Ungrounded Systems. If System Voltage Exceeds 300 Vdc, then 

Ungrounded Systems Only. 

Figure 4. Load Connected to Power Source. Grounded or 

Ungrounded Systems. 

Figure 5. Load Isolated from Power Source. Grounded or 

Ungrounded Systems. If System Voltage Exceeds 125 Vdc, then 

Ungrounded Systems Only. 

Power

Load

Power

Load

Breaker

Breaker

3 Pole

3 Pole

         

Load Isolated from Power Source.

Grounded or Ungrounded Systems.

If System Voltage Exceeds 300 Vdc.

Then Ungrounded Systems Only.

Fig. 5-2

Breaker

Load

Power

Breaker

Load

Power

2 Pole

2 Pole

         

Load Connected to Power Source.

Grounded or Ungrounded Systems.

Fig. 5-3

Breaker

Power

Load

2 Pole

Fig. 5-4

2. Installation

The installation procedure consists of inspecting the circuit  

breaker and, as applicable, installing  accessories, interphase 

barriers and terminals, mounting the circuit breaker, connecting the 

line and load conductors, torquing terminals, and attaching terminal 

shields. Circuit breakers, accessories,mounting hardware, 

and unmounted terminals may be supplied in separate 

packages. To install the circuit breaker, perform the following steps.
If required, internal accessory installation in any type of circuit 

breaker should be done before the circuit breaker is mounted and 

2-1. Make sure that the circuit breaker is suitable for the 

intended installation by comparing name-plate data with existing 

ratings and system requirements. Inspect the circuit breaker for 

completeness,and check for damage before mounting. 

 

2-2. Remove installed cover screws and cover.

 CAUTION

WHEN REMOVED AND REINSTALLED, THREAD-FORMING SCREWS  WILL 

TRY TO REFORM THE THREADS IN THE BASE . CARE SHOULD  BE TAKEN 

EVERY TIME A THREAD-FORMING SCREW IS USED TO ENSURE THE 

SCREW STARTS  IN THE ORIGINAL THREADS. DAMAGED THREADS CAN 

RESULT IN IMPROPER CIRCUIT BREAKER  COVER RETENTION.

 IL01202013E

H01

Summary of Contents for EG-DC Series









Reviews: