background image

19. With the display module facing down, remove the backlight cartridge by unscrewing the two screws 

holding the backlight cartridge to the display module and sliding gently apart about 1/8 inch and then 
lifting up. Figure 10 shows the backlight removed. 

 

Backlight 

Cable 

Video 

Connector 

Screw 

Screw

Backlight 

Cartridge

Display 
Module 

Figure 10 

20. Gently and carefully, place the new backlight cartridge into the display module, slide into position, 

and reattach the screws. Make sure the backlight cable is not crimped when you reattach the screws. 

Caution

:  The backlight cartridge is very fragile. Do not bend the backlight, but replace it by keeping 

the light perfectly straight. 

Cleaning

:  Clean off any fingerprints or dirt that may have gotten on the inner display surface or the 

backside of the front panel. 

21. Reattach the video cable to the video connector on the display module. See Figure 10. 

22. Insert the backlight cable through opening. 

23. Reattach the display to the display plate.  

24. Reattach the front panel to the display plate making sure that you push the touchscreen ribbon cable 

connector through the cutout in the display plate. Make sure all assembly screws have been 
retightened. 

25. Reattach the touchscreen jumper cable to the touchscreen connector. (See Figure 11.)  

 

Touchscreen 

Connector 

Touchscreen 

Jumper Cable 

Figure 11 

January 2006 

Page 8 of 14 

01-50604-01

 

 

Summary of Contents for Cutler-Hammer PanelMate Power Pro 1785...















Reviews: