background image

30

Eaton 93PM Universal Integrated Battery Cabinet (IBC-LW and IBC-LHW) Installation Manual P-164000541—Rev 04

2.

Remove the front door by loosening the left and right side bottom screws and removing four top screws
(see

Figure 9

) from the door. Lift the door to disengage the door from the bottom screws. Retain the

hardware for later use.

3.

Locate the four 1/2” jacking bolts from the parts bag packed inside the front door and install them in the
threaded holes in the front and rear supports as shown in

Figure 9

Place a floor protector from the parts kit

underneath each jacking bolt, and screw the bolts down against them.

The floor protectors protect the floor from being marred by the jacking bolts.

4.

Loosen, but do not remove, the skid mounting bolts holding the left, right, front, and rear to the pallet skids
(see

Figure 9

).

DO NOT

loosen or remove the cabinet mounting bolts or the cabinet support bolts.

WARNING

RISK OF INSTABILITY. Turning the jacking bolts unevenly may cause the cabinet to become unbalanced. To
prevent tipping the cabinet, raise the cabinet no more than 3 mm (1/8") above the floor (just enough to allow the
removal of the pallet skids). Failure to follow these instructions can result in serious injury or death.

5.

Turn each jacking bolt consecutively, two full turns, until the pallet skids clear the floor by approximately
3 mm (1/8").

NOTE

In the following step the center supports will drop away from the cabinet and the pallet
skids when the skids are removed.

6.

Remove the hardware loosened in

Step 4

.

7.

Pull the two pallet skids out from under the left, right, front, rear, and two center supports. Recycle the
pallet skids, supports, and hardware in a responsible manner.

Installation

Summary of Contents for 93PM IBC-LW















































































Reviews: