background image

Installation

Eaton 93E Integrated Accessory Cabinet-Distribution (30IAC-D and 60IAC-D) Installation and Operation Manual P-164000072—Rev 2

 www.eaton.com/powerquality

4-13

Figure 4-10. Bottom Conduit Landing Wire Entry Locations

4.4

Installing IAC-D External Power Wiring

To install wiring to connections:

1.

If installing wiring using conduit, continue to Step 2; if using the power terminal cover base channels, skip 
to Step 11.

2.

Identify all conduit requirements and mark their location on the IAC-D input conduit landing plate. Remove 
the conduit plate and drill or punch conduit holes, or remove knockouts in the conduit plate. Reinstall the 
conduit plate.

3.

Punch or drill holes in the bottom of the power terminal cover base on the UPS cabinet for the AC output 
conduit. Refer to the applicable Eaton 93E UPS installation and operation manual listed in paragraph 1.7 for 
UPS cabinet conduit landing location.

4.

Install conduit between the IAC-D and the UPS cabinet, IAC-T, IAC-B, or IAC-TB.

NOTE

The 93E 30IAC-D is shown. The 93E 60IAC-D conduit landing plate locations are the same.

93E 30IAC-D Bottom View

Front

Alternate Conduit Landing Plate for 
AC Input
(Remove panel to drill or punch 
conduit holes, or remove knockouts.)

Conduit Landing for AC Output from 
subfeed breakers
(Remove panel to drill or punch 
conduit holes, or remove knockouts.)

Conduit Landing for AC Output from 
distribution panelboard
(Remove panel to drill or punch 
conduit holes, or remove knockouts.)

NOTE 1

Wiring can be installed using conduit between cabinets or by routing wiring through 
the power terminal cover base wiring channels.

NOTE 2

Remove the IAC-D conduit landing plates to drill or punch conduit holes, or remove 
knockouts in the conduit plate (see Figure 4-9 or Figure 4-10).

NOTE 3

To aid in securing wiring and obtaining correct torque values, use a wire ferrule on 
small gauge wiring when installing to terminal lugs.

Summary of Contents for 93E 30IAC-D













































































Reviews: