background image

Page 19

620-00082-01-us (en)

ENGLISH

3. Installation

3.9 Communication ports 

Connection of RS232 or USB communication port

The RS232 and USB communication ports cannot operate simultaneously.

2

1

5

6

1.

  Connect the RS232 

(5)

 or USB  

(6) 

communication cable to  

the serial or USB port on  

the computer equipment.

2.

  Connect the other end of the 

communication cable 

(5)

 or 

(6)

 to the USB 

(1)

 or RS232 

(2)

 

communication port on  

the UPS.

The 

UPS

 can now communicate 

with EATON power management 

software.

Installation of the communication cards 

(optional, standard on the Network bundle models)

3

It is not necessary to shutdown 

the UPS before installing  

a communication card.

1.

  Remove the slot cover 

(3) 

secured by screws.

2.

  Insert the communication  

card in the slot.

3.

  Secure the card cover with  

the 2 screws. 

Characteristics of the optocouplers communication port 

(optional)

• 

Pins 1, 3, 4, 5, 6, 10: not used

• 

Pin 2: common (user)

• 

Pin 7: low battery

• 

 Pin 8: operation on battery 

power

• 

 Pin 9: UPS ON, equipment 

supplied

n.o.: normally open contact

When a signal is activated, the contact is closed between the common (pin 2) and the pin  

for the corresponding signal. 

Contact characteristics (optocoupler)

• 

Voltage: 48 V DC max

• 

Current: 25 mA max

• 

Power: 1.2 W

Summary of Contents for 5P 750





























Reviews: