background image

4. Battery maintenance

 

--17-- 

 

This series UPS only requires minimal maintenance. The battery used for standard 
models are value regulated sealed lead-acid maintenance free battery. These 
models require minimal repairs. The only requirement is to charge the UPS 
regularly in order to maximize the expected life of the battery. When being 
connected to the utility power, whether the UPS is turned on or not, the UPS keeps 
charging the batteries and also offers the protective function of overcharging and 
over-discharging. 

 

The UPS should be charged once every 4 to 6 months if it has not been used for a 
long time.   

 

In the regions of hot climates, the battery should be charged and discharged every 
2 months. The standard charging time should be at least 12 hours. 

 

Under normal conditions, the battery life lasts 3 to 5 years. In case if the battery is 
found not in good condition, earlier replacement should be made. Battery 
replacement should be performed by qualified personnel. 

 

Replace batteries with the same number and same type of batteries.         

 

Do not replace the battery individually. All the batteries should be replaced at the 
same time following the instructions of the battery supplier. 

 

Normally, the batteries should be charged and discharged once every 4 to 6 
months. Charging should begin after the UPS shuts down automatically in the 
course of discharging, the standard charging time for the standard UPS should be 
at least 12 hours.   

 

 

 

 

Summary of Contents for 10000HXL31



























Reviews: