Support Line: 0303 031 0777
For more innovative products from Easylife please visit:
www.easylifegroup.com
everyday solutions
™
Est. 1992
ELECTRODE PADS USE & MAINTENANCE
Please note a thin protective cover film on the underside of the butterfly shape electrode pad which
should be removed prior to being applied to the skin. It should not be discarded as it will be used to
protect the butterfly shape electrode after and when not in use.
Remember to wash and dry the skin area selected so that there is no excess oil, moisturiser, dead skin
cells, make-up or dust particles and these are removed before applying the butterfly shape electrode
pad. Once cleaned, the butterfly shape electrode pad would adhere to the selected skin area with ease.
If the adhesiveness of the electrode pad decreases or fades, this can be easily recovered by dropping
a couple of drops of water on the gel surface whilst spreading it evenly, do not dry it off with a cloth or
towel. Do not use too much water on the gel surface as this action will dissolve the adhesive layer.
When the electrode pad is not in use, return it to the protective film as soon as possible to ensure
its longevity and that no dust is attracted by the adhesive gel. The life of an electrode pad should be
around 40 to 50 applications. Please note that avoiding to store it as recommended or if you use the
electrode pads for extended periods, their longevity will be considerably shortened. However, this is
normal.
When removing the electrode pad from the selected area on the skin, please remember to hold the
electrode pad as well as the control unit.
HOW TO USE THE WIRELESS REMOTE CONTROL BUTTERFLY MASSAGER
Suggested areas to use your Butterfly Massager are shown below. Caution is always recommended
before all applications. Please remember that depending on the mode selected and the intensity level
desired, some moderate discomfort may be experienced. Either you should reduce the intensity level
selected or alternatively chose a different pulse mode. Variation of the times used, can also influence
the possible moderate discomfort and turn it into an effective and positive exercise.
TROUBLESHOOTING
SPARE PARTS & ACCESSORIES (Sold Seperately)
Product Code # EL6709
Butterfly Shape Electrode Pads x 4 (pack)
Troubleshooting
Causes
Solution
New batteries are installed,
but unit does not function.
Batteries polarity is incorrectly
installed
Re-install the battery with “+”
polarity face upwards
Batteries are installed cor-
rectly, but no function.
Batteries are discharged,
depleted or need to be
replaced.
Replace the batteries,
remember to use the same
type CR2032.
A slight skin rash after use
or moderate discomfort experi-
enced.
A. It may be caused by
increased circulation in this
particular area.
B. It may be because
the electrode is in a poor
condition.
C. The electrode pad requires
some maintenance.
A. It should disappear after a
short while.
B. Replace the electrodes with
new ones.
C. Ensure adhesiveness is
even through the pad.
No stimulation is felt, there is
no activity felt.
A. The electrode is dry or
does not contact with skin.
B. The electrode is torn,
broken or dirty.
C. The unit is defective.
A. Clean and re-apply
electrode
B. Replace electrode
C. Contact your supplier
Intermittent stimulation
(ensure is not the mode
selected).
A. Loose connection in the
unit or with the electrode.
B. Electrode gel surface is
torn or damaged.
A. Reconnect, making sure
contact is secure
B. Replace electrode
Not powerful enough
A. Electrode too dry, worn out
or dirty.
B. Battery running low.
C. Increase intensity level
selected
A. Re- apply new electrode
B. Replace battery as often as
required.
C. Maintain pulse activity to a
comfortable level.
Surges of power or intermit-
tent function.
A. Electrode peeling loose
from skin.
B. Ensure the correct mode is
selected.
A. Replace electrode or clean
if necessary.
B. Change the operation
mode by selecting a
different mode to test.
