Paper weight 60gsm
everyday solutions
™
Est. 1992
Support Line: 0844 441 8448
For more innovative products from Easylife please visit:
www.easylifegroup.com
Remark :
This system has an auto-stop mechanism, which stops the turntable revolving
when it gets to the end. On some records, where they are longer than normal, it may stop
before the end of the last track. In this happens, the Auto-stop switch (25) can be set to
the “ Off “ position, then it will run to the end of the record but will not stop automatically.
Turn off the unit using the power button or switch back the auto-stop switch back to the “
on “ position to stop the turntable rotating. Then replace the tone arm to the rest position.
Remark : Phono and Aux-In share a channel on this system. When a cable is plugged
in to the Aux in socket(28) the phono is disabled and the channel will change to Aux
automatically. Please ensure nothing is plugged in to the Aux in socket (28) before
using the turntable.
Aux-in connection
Connect the unit to any auxiliary device (i.e. MP3 player) by connecting it to the aux in
socket (28) on the rear of the music system. Using a 3.5mm stereo cable (not provided)
connect one end to your auxiliary device and one to the music system.
1. Select the “ Phono/Aux ” function(3).
2. Plug the cable from the auxiliary device in to the Aux in socket. The channel with switch
to Aux automatically.
3. Start playback on your device and adjust Power/Volume knob (5) to the desire volume
level. If there is distortion, reduce the volume level of your auxiliary device.
Note: To use the turntable unplug Aux leads as the phono is disabled with a cable in
the aux-in socket
Line out connection
You can connect this system to another Hi-Fi by connecting the line out socket (29) to an
auxiliary input socket with a RCA cable (not included).
Encoding of CD disc / Phono or Cassette tape into MP3 fi le
The system is able to encode from CD, Record (from phono) and cassette deck (from
tape) to MP3 format and record to a USB memory stick.
A) CD encoding
i) Recording 1 track
1. Plug in the USB pen drive for recording (make sure it has enough empty space).
2. Play the CD track you want to encode/record, as normal.
3. Press the “ Record “ button (9) during playback of the desired track
4. “ “&“ “ will be fl ashing on the LCD display (2) to show encoding is in progress.
5. After the encoding process has fi nished, the unit will stop playback automatically.
ii) Recording a complete CD
1. Place a CD with the printed side facing up inside the CD tray & then close the CD door.
2. After disc search has been completed, press the “ Record “ button (9) – note: please
do not press “ Play/Pause/Stop ” button (18) and then “record” button, otherwise, only the
played track will be recorded.
3. “ “&“ “ will be fl ashing on the LCD display (2) to show encoding is in progress.
4. After the encoding process has fi nished, the unit will stop playback automatically.
iii) Recoding by program
1. Place a CD with the printed side facing up inside the tray & then close the co door
2. Select the desire tracks by following the “ CD/MP3 disc programming “ procedure.
Then press “ Play/Pause/Stop “ button (18) to start playback.
3. Press the “ Record “ button (3) and the unit will display “ “&“ “ & fl ashing.
Encoding is performing now.
4. After completing of encoding, unit will stop playback automatically.
iv) Copying MP3 fi les
If using an MP3 disc instead of a CD-disc, the system will copy the fi les to the USB after
pressing the “ Record “ button (9). The operation procedure is the same as CD encoding
as stipulated above, and the system will switch to copying mode only if MP3 fi le being
read.
Remark:-
- The recording speed is 1:1 according to the actual playing time of the Phono or Tape
- During copy mode, the system will copy the MP3 fi le only.
- The system will create an “ audio “ folder for encoded fi les and “ fcopy “ for copied fi les.
- The recording format is preset at – MP3 bit rate : 128 kbps, sampling rate : 44.1khz
- No song title will be recorded during encoding mode
- To interrupt the recording, press the “ Record “ button again during the recording.
- Encoding CD to MP3 fi le or copying MP3 fi le to USB will be successful only if the entire
song is encoded or copied, if terminated the encoding or copying will not create a fi le on
the USB.
B) Phono encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Phono “ position and then press the “ Record “ button
(9) directly.
3) The LCD display (2) with show the word “ USB “ and fl ashing, after then display
“ “&“ “ and fl ashing. Now the system is starting the encoding mode.
4) Start playback on the record which you want to record to USB.
5) When you wish to fi nish recording press and hold the “ Record “ button (9) until the text
on LCD display (2) stops fl ashing and returns to “ Phono “ mode.
Line out connection
You can connect this system to another Hi-Fi by connecting the line out socket (29) to an auxiliary input socket with a
RCA cable (not included).
E
ncoding of CD disc / Phono or Cassette tape into MP3 file
The system is able to encode from CD, Record (from phono) and cassette deck (from tape) to MP3 format and record to
a USB memory stick.
A) CD encoding
i) Recording 1 track
1. Plug in the USB pen drive for recording (make sure it has enough empty space).
2. Play the CD track you want to encode/record, as normal.
3. Press the “ Record “ button (9) during playback of the desired track
4. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
5. After the encoding process has finished, the unit will stop playback automatically.
ii) Recording a complete CD
1. Place a CD with the printed side facing up inside the CD tray & then close the CD door.
2. After disc search has been completed, press the “ Record “ button (9) –
note:
please do not press
“ Play/Pause/Stop ” button (18) and then "record" button, otherwise, only the played track will be recorded.
3. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
4. After the encoding process has finished, the unit will stop playback automatically.
iii) Recoding by program
1. Place a CD with the printed side facing up inside the tray & then close the co door
2. Select the desire tracks by following the “
CD/MP3 disc programming
“ procedure. Then press
“ Play/Pause/Stop “ button (18) to start playback.
3. Press the “ Record “ button (3) and the unit will display “
“ & “
“ & flashing. Encoding is performing
now.
4. After completing of encoding, unit will stop playback automatically.
iv) Copying MP3 files
If using an MP3 disc instead of a CD-disc, the system will copy the files to the USB after pressing the “ Record “ button
(9). The operation procedure is the same as CD encoding as stipulated above, and the system will switch to copying
mode only if MP3 file being read.
Remark:-
-
The recording speed is 1:1 according to the actual playing time of the Phono or Tape
-
During copy mode, the system will copy the MP3 file only.
-
The system will create an “ audio “ folder for encoded files and “ fcopy “ for copied files.
-
The recording format is preset at – MP3
bit rate : 128 kbps, sampling rate : 44.1khz
-
No song title will be recorded during encoding mode
-
To interrupt the recording, press the “ Record “ button again during the recording.
-
Encoding CD to MP3 file or copying MP3 file to USB will be successful only if the entire song is encoded or copied,
if terminated the encoding or copying will not create a file on the USB.
B) Phono encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Phono “ position and then press the “ Record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“ and flashing.
Now the system is starting the encoding mode.
4) Start playback on the record which you want to record to USB.
5) When you wish to finish recording press and hold the “ Record “ button (9) until the text on LCD display (2) stops
flashing and returns to “ Phono “ mode.
C) Cassette encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Tape “ mode and then press the “ record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“flashing. Now
the system is starting the encoding mode.
4) Start playback of cassette tape at the point you wish to start recording.
5) When you wish to stop recording press and hold the “ Record “ button (9) until the symbol “
“ & “
“ disappears and returns to “ Tape “ mode on LCD display (2).
5
Line out connection
You can connect this system to another Hi-Fi by connecting the line out socket (29) to an auxiliary input socket with a
RCA cable (not included).
E
ncoding of CD disc / Phono or Cassette tape into MP3 file
The system is able to encode from CD, Record (from phono) and cassette deck (from tape) to MP3 format and record to
a USB memory stick.
A) CD encoding
i) Recording 1 track
1. Plug in the USB pen drive for recording (make sure it has enough empty space).
2. Play the CD track you want to encode/record, as normal.
3. Press the “ Record “ button (9) during playback of the desired track
4. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
5. After the encoding process has finished, the unit will stop playback automatically.
ii) Recording a complete CD
1. Place a CD with the printed side facing up inside the CD tray & then close the CD door.
2. After disc search has been completed, press the “ Record “ button (9) –
note:
please do not press
“ Play/Pause/Stop ” button (18) and then "record" button, otherwise, only the played track will be recorded.
3. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
4. After the encoding process has finished, the unit will stop playback automatically.
iii) Recoding by program
1. Place a CD with the printed side facing up inside the tray & then close the co door
2. Select the desire tracks by following the “
CD/MP3 disc programming
“ procedure. Then press
“ Play/Pause/Stop “ button (18) to start playback.
3. Press the “ Record “ button (3) and the unit will display “
“ & “
“ & flashing. Encoding is performing
now.
4. After completing of encoding, unit will stop playback automatically.
iv) Copying MP3 files
If using an MP3 disc instead of a CD-disc, the system will copy the files to the USB after pressing the “ Record “ button
(9). The operation procedure is the same as CD encoding as stipulated above, and the system will switch to copying
mode only if MP3 file being read.
Remark:-
-
The recording speed is 1:1 according to the actual playing time of the Phono or Tape
-
During copy mode, the system will copy the MP3 file only.
-
The system will create an “ audio “ folder for encoded files and “ fcopy “ for copied files.
-
The recording format is preset at – MP3
bit rate : 128 kbps, sampling rate : 44.1khz
-
No song title will be recorded during encoding mode
-
To interrupt the recording, press the “ Record “ button again during the recording.
-
Encoding CD to MP3 file or copying MP3 file to USB will be successful only if the entire song is encoded or copied,
if terminated the encoding or copying will not create a file on the USB.
B) Phono encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Phono “ position and then press the “ Record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“ and flashing.
Now the system is starting the encoding mode.
4) Start playback on the record which you want to record to USB.
5) When you wish to finish recording press and hold the “ Record “ button (9) until the text on LCD display (2) stops
flashing and returns to “ Phono “ mode.
C) Cassette encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Tape “ mode and then press the “ record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“flashing. Now
the system is starting the encoding mode.
4) Start playback of cassette tape at the point you wish to start recording.
5) When you wish to stop recording press and hold the “ Record “ button (9) until the symbol “
“ & “
“ disappears and returns to “ Tape “ mode on LCD display (2).
5
Line out connection
You can connect this system to another Hi-Fi by connecting the line out socket (29) to an auxiliary input socket with a
RCA cable (not included).
E
ncoding of CD disc / Phono or Cassette tape into MP3 file
The system is able to encode from CD, Record (from phono) and cassette deck (from tape) to MP3 format and record to
a USB memory stick.
A) CD encoding
i) Recording 1 track
1. Plug in the USB pen drive for recording (make sure it has enough empty space).
2. Play the CD track you want to encode/record, as normal.
3. Press the “ Record “ button (9) during playback of the desired track
4. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
5. After the encoding process has finished, the unit will stop playback automatically.
ii) Recording a complete CD
1. Place a CD with the printed side facing up inside the CD tray & then close the CD door.
2. After disc search has been completed, press the “ Record “ button (9) –
note:
please do not press
“ Play/Pause/Stop ” button (18) and then "record" button, otherwise, only the played track will be recorded.
3. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
4. After the encoding process has finished, the unit will stop playback automatically.
iii) Recoding by program
1. Place a CD with the printed side facing up inside the tray & then close the co door
2. Select the desire tracks by following the “
CD/MP3 disc programming
“ procedure. Then press
“ Play/Pause/Stop “ button (18) to start playback.
3. Press the “ Record “ button (3) and the unit will display “
“ & “
“ & flashing. Encoding is performing
now.
4. After completing of encoding, unit will stop playback automatically.
iv) Copying MP3 files
If using an MP3 disc instead of a CD-disc, the system will copy the files to the USB after pressing the “ Record “ button
(9). The operation procedure is the same as CD encoding as stipulated above, and the system will switch to copying
mode only if MP3 file being read.
Remark:-
-
The recording speed is 1:1 according to the actual playing time of the Phono or Tape
-
During copy mode, the system will copy the MP3 file only.
-
The system will create an “ audio “ folder for encoded files and “ fcopy “ for copied files.
-
The recording format is preset at – MP3
bit rate : 128 kbps, sampling rate : 44.1khz
-
No song title will be recorded during encoding mode
-
To interrupt the recording, press the “ Record “ button again during the recording.
-
Encoding CD to MP3 file or copying MP3 file to USB will be successful only if the entire song is encoded or copied,
if terminated the encoding or copying will not create a file on the USB.
B) Phono encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Phono “ position and then press the “ Record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“ and flashing.
Now the system is starting the encoding mode.
4) Start playback on the record which you want to record to USB.
5) When you wish to finish recording press and hold the “ Record “ button (9) until the text on LCD display (2) stops
flashing and returns to “ Phono “ mode.
C) Cassette encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Tape “ mode and then press the “ record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“flashing. Now
the system is starting the encoding mode.
4) Start playback of cassette tape at the point you wish to start recording.
5) When you wish to stop recording press and hold the “ Record “ button (9) until the symbol “
“ & “
“ disappears and returns to “ Tape “ mode on LCD display (2).
5
Line out connection
You can connect this system to another Hi-Fi by connecting the line out socket (29) to an auxiliary input socket with a
RCA cable (not included).
E
ncoding of CD disc / Phono or Cassette tape into MP3 file
The system is able to encode from CD, Record (from phono) and cassette deck (from tape) to MP3 format and record to
a USB memory stick.
A) CD encoding
i) Recording 1 track
1. Plug in the USB pen drive for recording (make sure it has enough empty space).
2. Play the CD track you want to encode/record, as normal.
3. Press the “ Record “ button (9) during playback of the desired track
4. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
5. After the encoding process has finished, the unit will stop playback automatically.
ii) Recording a complete CD
1. Place a CD with the printed side facing up inside the CD tray & then close the CD door.
2. After disc search has been completed, press the “ Record “ button (9) –
note:
please do not press
“ Play/Pause/Stop ” button (18) and then "record" button, otherwise, only the played track will be recorded.
3. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
4. After the encoding process has finished, the unit will stop playback automatically.
iii) Recoding by program
1. Place a CD with the printed side facing up inside the tray & then close the co door
2. Select the desire tracks by following the “
CD/MP3 disc programming
“ procedure. Then press
“ Play/Pause/Stop “ button (18) to start playback.
3. Press the “ Record “ button (3) and the unit will display “
“ & “
“ & flashing. Encoding is performing
now.
4. After completing of encoding, unit will stop playback automatically.
iv) Copying MP3 files
If using an MP3 disc instead of a CD-disc, the system will copy the files to the USB after pressing the “ Record “ button
(9). The operation procedure is the same as CD encoding as stipulated above, and the system will switch to copying
mode only if MP3 file being read.
Remark:-
-
The recording speed is 1:1 according to the actual playing time of the Phono or Tape
-
During copy mode, the system will copy the MP3 file only.
-
The system will create an “ audio “ folder for encoded files and “ fcopy “ for copied files.
-
The recording format is preset at – MP3
bit rate : 128 kbps, sampling rate : 44.1khz
-
No song title will be recorded during encoding mode
-
To interrupt the recording, press the “ Record “ button again during the recording.
-
Encoding CD to MP3 file or copying MP3 file to USB will be successful only if the entire song is encoded or copied,
if terminated the encoding or copying will not create a file on the USB.
B) Phono encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Phono “ position and then press the “ Record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“ and flashing.
Now the system is starting the encoding mode.
4) Start playback on the record which you want to record to USB.
5) When you wish to finish recording press and hold the “ Record “ button (9) until the text on LCD display (2) stops
flashing and returns to “ Phono “ mode.
C) Cassette encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Tape “ mode and then press the “ record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“flashing. Now
the system is starting the encoding mode.
4) Start playback of cassette tape at the point you wish to start recording.
5) When you wish to stop recording press and hold the “ Record “ button (9) until the symbol “
“ & “
“ disappears and returns to “ Tape “ mode on LCD display (2).
5
Line out connection
You can connect this system to another Hi-Fi by connecting the line out socket (29) to an auxiliary input socket with a
RCA cable (not included).
E
ncoding of CD disc / Phono or Cassette tape into MP3 file
The system is able to encode from CD, Record (from phono) and cassette deck (from tape) to MP3 format and record to
a USB memory stick.
A) CD encoding
i) Recording 1 track
1. Plug in the USB pen drive for recording (make sure it has enough empty space).
2. Play the CD track you want to encode/record, as normal.
3. Press the “ Record “ button (9) during playback of the desired track
4. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
5. After the encoding process has finished, the unit will stop playback automatically.
ii) Recording a complete CD
1. Place a CD with the printed side facing up inside the CD tray & then close the CD door.
2. After disc search has been completed, press the “ Record “ button (9) –
note:
please do not press
“ Play/Pause/Stop ” button (18) and then "record" button, otherwise, only the played track will be recorded.
3. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
4. After the encoding process has finished, the unit will stop playback automatically.
iii) Recoding by program
1. Place a CD with the printed side facing up inside the tray & then close the co door
2.
Select the desire tracks by following the “
CD/MP3 disc programming
“ procedure. Then press
“ Play/Pause/Stop “ button (18) to start playback.
3. Press the “ Record “ button (3) and the unit will display “
“ & “
“ & flashing. Encoding is performing
now.
4. After completing of encoding, unit will stop playback automatically.
iv) Copying MP3 files
If using an MP3 disc instead of a CD-disc, the system will copy the files to the USB after pressing the “ Record “ button
(9). The operation procedure is the same as CD encoding as stipulated above, and the system will switch to copying
mode only if MP3 file being read.
Remark:-
-
The recording speed is 1:1 according to the actual playing time of the Phono or Tape
-
During copy mode, the system will copy the MP3 file only.
-
The system will create an “ audio “ folder for encoded files and “ fcopy “ for copied files.
-
The recording format is preset at – MP3
bit rate : 128 kbps, sampling rate : 44.1khz
-
No song title will be recorded during encoding mode
-
To interrupt the recording, press the “ Record “ button again during the recording.
-
Encoding CD to MP3 file or copying MP3 file to USB will be successful only if the entire song is encoded or copied,
if terminated the encoding or copying will not create a file on the USB.
B) Phono encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Phono “ position and then press the “ Record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“ and flashing.
Now the system is starting the encoding mode.
4) Start playback on the record which you want to record to USB.
5) When you wish to finish recording press and hold the “ Record “ button (9) until the text on LCD display (2) stops
flashing and returns to “ Phono “ mode.
C) Cassette encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Tape “ mode and then press the “ record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“flashing. Now
the system is starting the encoding mode.
4) Start playback of cassette tape at the point you wish to start recording.
5) When you wish to stop recording press and hold the “ Record “ button (9) until the symbol “
“ & “
“ disappears and returns to “ Tape “ mode on LCD display (2).
5
Line out connection
You can connect this system to another Hi-Fi by connecting the line out socket (29) to an auxiliary input socket with a
RCA cable (not included).
E
ncoding of CD disc / Phono or Cassette tape into MP3 file
The system is able to encode from CD, Record (from phono) and cassette deck (from tape) to MP3 format and record to
a USB memory stick.
A) CD encoding
i) Recording 1 track
1. Plug in the USB pen drive for recording (make sure it has enough empty space).
2. Play the CD track you want to encode/record, as normal.
3. Press the “ Record “ button (9) during playback of the desired track
4. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
5. After the encoding process has finished, the unit will stop playback automatically.
ii) Recording a complete CD
1. Place a CD with the printed side facing up inside the CD tray & then close the CD door.
2. After disc search has been completed, press the “ Record “ button (9) –
note:
please do not press
“ Play/Pause/Stop ” button (18) and then "record" button, otherwise, only the played track will be recorded.
3. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
4. After the encoding process has finished, the unit will stop playback automatically.
iii) Recoding by program
1. Place a CD with the printed side facing up inside the tray & then close the co door
2.
Select the desire tracks by following the “
CD/MP3 disc programming
“ procedure. Then press
“ Play/Pause/Stop “ button (18) to start playback.
3. Press the “ Record “ button (3) and the unit will display “
“ & “
“ & flashing. Encoding is performing
now.
4. After completing of encoding, unit will stop playback automatically.
iv) Copying MP3 files
If using an MP3 disc instead of a CD-disc, the system will copy the files to the USB after pressing the “ Record “ button
(9). The operation procedure is the same as CD encoding as stipulated above, and the system will switch to copying
mode only if MP3 file being read.
Remark:-
-
The recording speed is 1:1 according to the actual playing time of the Phono or Tape
-
During copy mode, the system will copy the MP3 file only.
-
The system will create an “ audio “ folder for encoded files and “ fcopy “ for copied files.
-
The recording format is preset at – MP3
bit rate : 128 kbps, sampling rate : 44.1khz
-
No song title will be recorded during encoding mode
-
To interrupt the recording, press the “ Record “ button again during the recording.
-
Encoding CD to MP3 file or copying MP3 file to USB will be successful only if the entire song is encoded or copied,
if terminated the encoding or copying will not create a file on the USB.
B) Phono encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Phono “ position and then press the “ Record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“ and flashing.
Now the system is starting the encoding mode.
4) Start playback on the record which you want to record to USB.
5) When you wish to finish recording press and hold the “ Record “ button (9) until the text on LCD display (2) stops
flashing and returns to “ Phono “ mode.
C) Cassette encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Tape “ mode and then press the “ record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“flashing. Now
the system is starting the encoding mode.
4) Start playback of cassette tape at the point you wish to start recording.
5) When you wish to stop recording press and hold the “ Record “ button (9) until the symbol “
“ & “
“ disappears and returns to “ Tape “ mode on LCD display (2).
5
Line out connection
You can connect this system to another Hi-Fi by connecting the line out socket (29) to an auxiliary input socket with a
RCA cable (not included).
E
ncoding of CD disc / Phono or Cassette tape into MP3 file
The system is able to encode from CD, Record (from phono) and cassette deck (from tape) to MP3 format and record to
a USB memory stick.
A) CD encoding
i) Recording 1 track
1. Plug in the USB pen drive for recording (make sure it has enough empty space).
2. Play the CD track you want to encode/record, as normal.
3. Press the “ Record “ button (9) during playback of the desired track
4. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
5. After the encoding process has finished, the unit will stop playback automatically.
ii) Recording a complete CD
1. Place a CD with the printed side facing up inside the CD tray & then close the CD door.
2. After disc search has been completed, press the “ Record “ button (9) –
note:
please do not press
“ Play/Pause/Stop ” button (18) and then "record" button, otherwise, only the played track will be recorded.
3. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
4. After the encoding process has finished, the unit will stop playback automatically.
iii) Recoding by program
1. Place a CD with the printed side facing up inside the tray & then close the co door
2.
Select the desire tracks by following the “
CD/MP3 disc programming
“ procedure. Then press
“ Play/Pause/Stop “ button (18) to start playback.
3. Press the “ Record “ button (3) and the unit will display “
“ & “
“ & flashing. Encoding is performing
now.
4. After completing of encoding, unit will stop playback automatically.
iv) Copying MP3 files
If using an MP3 disc instead of a CD-disc, the system will copy the files to the USB after pressing the “ Record “ button
(9). The operation procedure is the same as CD encoding as stipulated above, and the system will switch to copying
mode only if MP3 file being read.
Remark:-
-
The recording speed is 1:1 according to the actual playing time of the Phono or Tape
-
During copy mode, the system will copy the MP3 file only.
-
The system will create an “ audio “ folder for encoded files and “ fcopy “ for copied files.
-
The recording format is preset at – MP3
bit rate : 128 kbps, sampling rate : 44.1khz
-
No song title will be recorded during encoding mode
-
To interrupt the recording, press the “ Record “ button again during the recording.
-
Encoding CD to MP3 file or copying MP3 file to USB will be successful only if the entire song is encoded or copied,
if terminated the encoding or copying will not create a file on the USB.
B) Phono encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Phono “ position and then press the “ Record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“ and flashing.
Now the system is starting the encoding mode.
4) Start playback on the record which you want to record to USB.
5) When you wish to finish recording press and hold the “ Record “ button (9) until the text on LCD display (2) stops
flashing and returns to “ Phono “ mode.
C) Cassette encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Tape “ mode and then press the “ record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“flashing. Now
the system is starting the encoding mode.
4) Start playback of cassette tape at the point you wish to start recording.
5) When you wish to stop recording press and hold the “ Record “ button (9) until the symbol “
“ & “
“ disappears and returns to “ Tape “ mode on LCD display (2).
5
Line out connection
You can connect this system to another Hi-Fi by connecting the line out socket (29) to an auxiliary input socket with a
RCA cable (not included).
E
ncoding of CD disc / Phono or Cassette tape into MP3 file
The system is able to encode from CD, Record (from phono) and cassette deck (from tape) to MP3 format and record to
a USB memory stick.
A) CD encoding
i) Recording 1 track
1. Plug in the USB pen drive for recording (make sure it has enough empty space).
2. Play the CD track you want to encode/record, as normal.
3. Press the “ Record “ button (9) during playback of the desired track
4. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
5. After the encoding process has finished, the unit will stop playback automatically.
ii) Recording a complete CD
1. Place a CD with the printed side facing up inside the CD tray & then close the CD door.
2. After disc search has been completed, press the “ Record “ button (9) –
note:
please do not press
“ Play/Pause/Stop ” button (18) and then "record" button, otherwise, only the played track will be recorded.
3. “
“ & “
“ will be flashing on the LCD display (2) to show encoding is in progress.
4. After the encoding process has finished, the unit will stop playback automatically.
iii) Recoding by program
1. Place a CD with the printed side facing up inside the tray & then close the co door
2.
Select the desire tracks by following the “
CD/MP3 disc programming
“ procedure. Then press
“ Play/Pause/Stop “ button (18) to start playback.
3. Press the “ Record “ button (3) and the unit will display “
“ & “
“ & flashing. Encoding is performing
now.
4. After completing of encoding, unit will stop playback automatically.
iv) Copying MP3 files
If using an MP3 disc instead of a CD-disc, the system will copy the files to the USB after pressing the “ Record “ button
(9). The operation procedure is the same as CD encoding as stipulated above, and the system will switch to copying
mode only if MP3 file being read.
Remark:-
-
The recording speed is 1:1 according to the actual playing time of the Phono or Tape
-
During copy mode, the system will copy the MP3 file only.
-
The system will create an “ audio “ folder for encoded files and “ fcopy “ for copied files.
-
The recording format is preset at – MP3
bit rate : 128 kbps, sampling rate : 44.1khz
-
No song title will be recorded during encoding mode
-
To interrupt the recording, press the “ Record “ button again during the recording.
-
Encoding CD to MP3 file or copying MP3 file to USB will be successful only if the entire song is encoded or copied,
if terminated the encoding or copying will not create a file on the USB.
B) Phono encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Phono “ position and then press the “ Record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“ and flashing.
Now the system is starting the encoding mode.
4) Start playback on the record which you want to record to USB.
5) When you wish to finish recording press and hold the “ Record “ button (9) until the text on LCD display (2) stops
flashing and returns to “ Phono “ mode.
C) Cassette encoding
1) Plug in the USB pen drive for recording (make sure it has enough empty space).
2) Set the function button (3) to “ Tape “ mode and then press the “ record “ button (9) directly.
3) The LCD display (2) with show the word “
USB
“ and flashing, after then display “
“ & “
“flashing. Now
the system is starting the encoding mode.
4) Start playback of cassette tape at the point you wish to start recording.
5) When you wish to stop recording press and hold the “ Record “ button (9) until the symbol “
“ & “
“ disappears and returns to “ Tape “ mode on LCD display (2).
5
EL6174_6_in_1_Music_System-8pp_A5-CMYK.indd 10-11
18/08/2015 09:45
