Eastwood flux core 90 Assembly & Operating Instructions Download Page 7 | Manualshive

Page: 7 / 21

background image

7

Eastwood Technical Assistance: 800.544.5118 >> [email protected]

• To prevent injury wear approved safety glasses.

MAGNETIC FIELDS CAN AFFECT PACEMAKERS!

• Any user with a pacemaker should consult their doctor before use.
• Anyone with a pacemaker should stay away from any welding without consultant

from a doctor.

NOTICE!

Do not touch the contact tip with the unit turned ‘ON’. Turn the unit ‘OFF’ before

changing tips or cleaning the nozzle.

«
...
5
6
7
8
9
...
»

Summary of Contents for flux core 90






















Reviews:

No comments

Related manuals for flux core 90

Brand: iDance Pages: 25

PlayWorks PS2000 Digital

Brand: Cambridge SoundWorks Pages: 22

Brand: CAME Pages: 24

MegaWorks THX 2.1 250D

Brand: Cambridge SoundWorks Pages: 13

Brand: Cambridge SoundWorks Pages: 14

Brand: Eaton Pages: 12

Brand: EAW Pages: 2

Brand: EAW Pages: 20

Brand: JBL Pages: 2

Simply Cinema ESC333

Brand: JBL Pages: 16

Project K2.S5500

Brand: JBL Pages: 2

Brand: JBL Pages: 8

Brand: Panasonic Pages: 2

Brand: JBL Pages: 2

Authentics L 16

Brand: JBL Pages: 11

Brand: Panasonic Pages: 1

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands