manualshive.com logo in svg

Eastey TT Series, User Manual

Share
Download
Eastey TT Series User Manual Download Page 31

Warranty Statement   31 

 

Warranty Statement 

 

Eastey TT Series Rotary Accumulation Table 

 

Warranty Statement 

Eastey Enterprises warrants that all of the products it ships will be in good working order 
and free from defects in material and workmanship and will conform to the published 
specifications for that product. 
 

Warranty Period 

 
 

Drive motor(s): 

1 year 

 
All other parts: 

1 year (Except for moving parts which are subject to normal 
wear, tear and replacement which are warranted to be free 
from defects in material and workmanship.) 

 
Operation Quality 

Quality of operation achieved in a given application is dependent on the installation, the 
material handling, and the maintenance provided. Eastey  makes no warranty that the 
quality achieved in an application will be the same as that achieved in our demo facility. 
 

Shipping Policy 

Customer pays  all incoming shipping. If the item is defective and under warranty, 
Eastey  pays return shipping charges for least costly method. If expedited shipping is 
desired, customer must furnish his shipping account and shipping fees will be charged 
to that account. 
 

Warranty Verification 

If you conclude that a product may be defective and may be covered by warranty, 
obtain a Return Material Authorization number by calling our technical support number 
(toll free at 1-800-835-9344, or 763-428-4846 or Fax: 763-795-8867) or e-mail: 
[email protected],  and return the defective item to Eastey.  Eastey  will analyze the 
product and, if found to be defective, we will, at our option, replace or repair the item. If 
the item is found to not be eligible for warranty, you will be notified and may decide on 
disposition. Defective products will be replaced or repaired as promptly as possible. 
 

Warranty Eligibility

 

The warranty provided by Eastey Enterprises, Inc. is only to the original buyer. 
 

Limited Warranty 

THE ABOVE WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER 
WARRANTIES, WHETHER EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED 
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE 
AND NONINFRINGEMENT. 
 

Summary of Contents for TT Series



































Reviews:

No comments

Brands by name

Popular brands

Load more brands