background image

18     XJ-300FR Manual

Earthquake Sound Corp.  |  www.earthquakesound.com

5 Year Limited Warranty

 

Earthquake  warrants  the  original  purchaser  that  the  speaker  or 

amplifier  (product)  is  free  from  defects  in  material  and  workmanship,  under 
normal and proper use, for a period of five (5) years from the date of purchase 
(as shown on the original sales receipt with the serial number affixed/written 
on it).
 

The five (5) years warranty period is valid only if the product is properly 

installed  by  an  Earthquake  authorized  party,  and  the  warranty  registration 
card is properly filled out and sent to Earthquake Sound Corporation. 

If the 

product is installed by a non-authorized party, a thirty (30) days warranty 
period applies.

(A) Five (5) years limited warranty plan coverage guidelines (If installed by an 
authorized Earthquake dealer):
 

•    First  year:  Earthquake  pays  for  labor,  parts,  and  ground  freight 

(only in the U.S. mainland, not including Alaska and Hawaii) 

back to the customer.

 

•    Second,  third,  fourth,  and  fifth  year:  Earthquake  pays  for  labor 

only.  Customer must pay for parts and freight both ways.

(B) Warning:
 

•   Products (sent for repair) that are tested by Earthquake technicians 

and deemed to have no problem, will not be covered by the five 
(5)  years  limited  warranty.  Customer  will  be  charged  a  minimum 
of one (1) hour of labor (ongoing rates) plus shipping back to the 
customer.

 

•   Each  product  sent  for  repair  must  be  packaged  in  its  original 

packaging.  Otherwise, 

there  will  be  a  repackaging  charge  in 

addition to labor, parts, and shipping charges.

(C) Earthquake agrees to repair or replace, at our option, all such defective 
products/parts subject to the following provisions:
 

•   Defective products/parts have not been altered or repaired by other 

than an Earthquake factory approved technician.

 

•   Products/parts are not subjected to negligence, misuse, improper 

use,  or  accident,  damaged  by  improper  line  voltage,  used  with 
incompatible products, or have its serial number or any part of it 
altered,  defaced,  removed,  or  have  been  used  in  anyway  that  is 
contrary to Earthquake’s written instructions.  

(D) Warranty Limitations: 
Earthquake warranty does not cover products that have been modified and/or 
abused, including but not limited to the following:
 

•   Damages to unit cover and finish due to misuse, abuse, or improper 

use of cleaning materials/methods.

 

•   Bent casing, damaged finish on casing due to abuse, misuse, or 

improper frame or broken connections.

Summary of Contents for XJ-300 FR





















Reviews: