Operator's Manual
Trail Warrior Quick Split 12-Ton Log Splitters
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5
26
MaINTENaNCE aND STORaGE
Good maintenance is essential for safe, economical, and trouble-
free operation. It will also help reduce air pollution. To help you
properly care for your engine, this manual includes maintenance
tips, routine inspection procedures, and simple maintenance
procedures using basic hand tools. Other service tasks that
are more difficult, or require special tools, are best handled by
professionals and are normally performed by a technician or
other qualified mechanic.
Maintenance, replacement or repair of the emissions control
devices and systems may be performed by any non-road
engine repair establishment or individuals. However, items
must be serviced by an authorized dealer to obtain "no
charge" emissions control service.
If you operate your engine under unusual conditions, such as
sustained high-load or high-temperature operation, or use in
unusually wet or dusty conditions, consult your servicing dealer
for recommendations applicable to your individual needs and use.
1. Consult the operating and maintenance instructions of
the engine operator’s manual for engine care and main-
tenance.
2. Always check the fluid level of the hydraulic reservoir before
operation. Fluid must register on the fill cap's dipstick when
the cylinder ram is in the return position. For caps that are not
equipped with a dipstick, fluid must be visible when looking
into the fill port when the log splitter is positioned on a level
surface. Operating the log splitter without an adequate fluid
supply will cause severe damage to the hydraulic pump.
3. All replacement parts must meet manufacturer’s specifications.
4. Check air pressure of tires before each use. Maintain pressure
of 30 psi.
NOTE: To relieve pressure from the entire hydraulic system,
hold the Flow Control valve lever in the rearward position,
while moving the direction control valve lever alternately
between the forward and rearward positions.
SPaRE PaRTS
ONLY use approved Ardisam spare parts.
TROUBLESHOOTING aND REPaIR
At Earthquake, we build quality and durability into the design of our
products; but no amount of careful design by us, and careful main-
tenance by you, can guarantee a repair-free life for your Earthquake
Log Splitter. Most repairs will be minor, and easily fixed by follow-
ing the suggestions in the troubleshooting guide in this section.
The troubleshooting guide will help you pinpoint the causes of
common problems and identify remedies.
For more complicated repairs, you may want to rely on your
retailer, an authorized service center or Earthquake. Earthquake
will make the necessary repairs if a service center is not available.
A parts breakdown is located toward the end of this manual.
We will always be glad to answer any questions you have, or help
you find suitable assistance. To order parts or inquire about warranty,
call or e-mail us using the contact information found in this section.
ORDERING REPLaCEMENT PaRTS
Parts can be obtained from the store where the log splitter was
purchased or direct from the factory. To order parts visit www.
getearthquake.com or call 1-800-345-6007.
For other general questions, you can e-mail us at [email protected].
Please include the following information with your order:
1) Part numbers
2) Part description
3) Quantity
4) Model number and serial number
TRaNSPORTING yOUR LOG SPLITTER
See the accompanying engine manual for additional transpor-
tation instructions.
1. After using the log splitter and before transporting it in a
truck bed, screw the gas cap screw and gas cap on (clock-
wise) tightly. The gas cap will not leak during transporting if
gas cap is tight and the screw at the top is tight. Never trans-
port engine inside an enclosed space within a vehicle. Fuel
or fuel vapors may ignite causing serious injury or death.
2. If fuel is present in the fuel tank, transport in an open vehicle
in an upright position.
3. If an enclosed vehicle must be used, remove gas into an ap-
proved red fuel container. DO NOT siphon by mouth.
4. Run engine to use up the fuel in the carburetor and fuel
tank. Always run engine in a well-ventilated area.
5. Wipe away any spilled fuel from engine and splitter. Allow to dry.
6. Gas cap and gas cap vent screw should be turned down tightly
before transporting splitter in a vehicle.
LONG-TERM STORaGE
If your log splitter will not be used for more than one month,
prepare it for long-term storage.
Steps for Long-Term Storage
1. Remove the remainder of the fuel from the gas tank into an
approved fuel container.
2. Store splitter in a horizontal position.
3. Remove all debris from cradle area and engine.
