background image

OPERATOR INSTRUCTIONS ANd PARTS 

MC43E & MC43 Mini Cultivator

Page 1

GetEarthquake.com

800-45-6007

3.  Move choke lever to 

ChOkE 

position.

  note: choke position is defined by moving the 

choke lever as far to the choke position as pos-
sible. 

4.  Push rocker switch to the 

ON

 position.

5.  Squeeze throttle control with right hand. Grasp starter 

handle with left hand and pull out slowly, until it pulls 
slightly harder. Without letting starter handle retract, pull 
rope with a rapid full arm stroke. Let it return to its original 
position very slowly until unit fires or runs. Repeat this 
step every time the starter rope is pulled.

  note: if engine fails to start after 5-6 pulls, push 

primer 1 time and pull starter rope again. 

6.  After engine starts running, move choke lever to 

hALF 

ChOkE

 position until unit runs smoothly.

  note:  halF  choke  is  defined  when  the  choke 

lever is between choke and run.

7.  Move choke lever to 

RUN

 position and move throttle to 

desired speed.

  note: run at full throttle when possible. do not let 

unit idle for extended periods of time.

8.  To stop engine, push rocker switch to 

OFF

 position.

WARM ENGINE START:

1.  Move choke lever to 

ChOkE

 position.

  note: choke position is defined by moving the 

choke lever as far to the choke position as pos-
sible.

2.  Continue with Step 4 of Cold Engine Starting.

hOT ENGINE START:

1.  Continue with Step 4 of Cold Engine Starting.
2.  If engine does not fire, refer to Step 1 of Warm Engine 

Starting.

FOR MOdEL MC4E ELECTRIC START

1.  Check  that  the  battery  is  connected  using  the  white 

plastic connectors inside the battery box. Insert ignition 
key  into  ignition  and  turn  key  to  the  START  position 
until engine starts running, then release key to the ON 
position. 

dO NOT

 hold the ignition key in the START 

position longer than 3 seconds.

2.  Run  engine  for  30  to  45  seconds  at  hALF  ChOKE 

position until engine warms up.

3.  Move choke lever to RUN position and move throttle to 

desired speed.

4.  To stop, turn switch to OFF position on manual start 

models. On electric start, turn ignition key to the OFF 
position.

dO  NOT  attempt  to  start  engine  in  the  following 
ways:

•   

dO NOT

 use starting fluid.

•   

dO  NOT

  spray  flammable  liquids  or  vapors  into  air 

cleaner, carburetor or spark plug chamber.

•   

dO NOT

 remove spark plug and attempt to start engine. 

Flammable fuel can spray out & ignite from a spark from 
spark plug.

Summary of Contents for MC43

































Reviews: