background image

31

Check for parts online at 

www.getearthquake.com

 or call 800-345-6007 M-F 8-5

Operator’s Manual 

6015 Series CRT Rototiller

Explanation of Emissions Control (6015V) 

Warranty Provisions

Viper® Engines are designed, built and equipped to meet all EPA requirements.  

It warrants that it is free from defects in material and workmanship that could 

cause failure to the warranted part; and that it is identical in all material 

respects to the engine described in the manufacturer’s application for 
certification. When a warrantable condition exists, Ardisam will repair your 
engine at no cost to you, including parts and labor.  The engine emissions 
label will indicate certification information.   Purchasers located more than 
100 miles from a Viper® authorized repair center in need of warrantable 
repair should contact customer service.  If it is determined that warranted 
repair is indeed necessary, Ardisam, Inc., will cover the cost of shipping to an 
authorized Viper® repair center.  All such requests must first be pre-approved 
by customer service prior to shipping.

Listed below are the parts covered by the emissions control systems 

warranty.  Some parts listed below may require scheduled maintenance and 
are warranted up to the first scheduled replacement point for that part.  See 
maintenance schedule in Maintenance and Storage section of manual for 
more details.  Coverage under this warranty includes only the parts listed 
below (the emission and evaporation control systems) if so equipped:

•  Air Filter Assembly (only to the first scheduled replacement point)
•  Fuel Filter (only to the first scheduled replacement point)
•  Carburetor
•  Fuel Lines, Fuel Line Fittings and Clamps
•  Fuel Metering Valve (if equipped)
•  Evaporative System (if equipped)

    - Canister (if equipped)
    - Canister filter (if equipped)
    - Vapor hose (if equipped)
    - Orifice connector (if equipped)
    - Fuel tank
    - Fuel cap
    - Primer bulb canister (if equipped)

•  Spark Plugs
•  Magneto Ignition System 
•  Muffler Assembly

LIMITATIONS

T

he Emission Control Systems Warranty shall not cover any of the following:

a) Repair or replacement required because of misuse or neglect, improper 

maintenance, repairs improperly performed or replacements not 

conforming to Ardisam, Inc., specifications that adversely affect 

performance and/or durability and alterations or modifications not 

recommended or approved in writing by Ardisam, Inc.

b) Replacement of parts and other services and adjustments necessary for 

required maintenance at or after the first scheduled replacement point;

c) Consequential damages such as loss of time, inconvenience, loss of use 

of the engine or equipment, etc.

d) Diagnosis and inspection fees that do not result in eligible warranty 

service being performed; and

e) Any add-on or modified part, or malfunction of authorized parts due to 

the use of add-on  or modified parts.  

These items will be covered for a period of 

two years

 from the date of the 

original purchase.  Viper warrants that: the components are designed, built 
and equipped so as to conform with all applicable regulations adopted 

by the EPA; that they are free from defects in material and workmanship 
that could cause failure to the engine or other; and that the components 

used are identical in all material respects to the engine described in the 
manufacturer’s application for certification.  The warranty period begins on 
the date the engine is originally purchased. 

MAINTENANCE AND REPAIR REQUIREMENTS

The owner is responsible for the proper use and maintenance of the engine.  

Ardisam, Inc. recommends that all receipts and records covering the 

performance of regular maintenance be retained in case questions arise.  If 

the engine is resold during the warranty period, the maintenance records 

should be transferred to each subsequent owner.  Ardisam, Inc. reserves 

the right to deny warranty coverage if the engine has not been properly 

maintained; however, Ardisam, Inc. may not deny warranty repairs solely 

because of failure to keep maintenance records.

Normal maintenance replacement or repair of emission control devices 

and  systems  may  be  performed  by  any  repair  establishment  or  individuals;  

however, warranty repairs must be performed by an Ardisam authorized service 

center.  Any replacement parts or service that is equivalent in performance and 

durability may be used in non-warranty maintenance or repairs, and shall not 

reduce the warranty obligations of the engine manufacturer. 

The warranty on emissions-related parts is as follows:

•  Any  warranted  part  that  is  not  scheduled  for  replacement  as  required 

maintenance in the owner’s manual supplied, is warranted for the warranty 
period stated above.  If any such part fails during the period of warranty 
coverage, that part will be repaired or replaced at no charge to the owner.  
Any such part repaired or replaced under the warranty will be warranted for 
the remaining warranty period.

•  Any warranted part that is scheduled only for regular inspection in the 

owner’s manual supplied, is warranted for the warranty period.  Any 
such part repaired or replaced under warranty will be warranted for the 
remaining warranty period.

•  Any  warranted  part  that  is  scheduled  for  replacement  as  required 

maintenance in the owner’s manual supplied, is warranted  for the period of 
time prior to the first scheduled replacement point for that part.  If the part 
fails prior to the first scheduled replacement, the part will be repaired or 
replaced at no charge to the owner.  Any such part repaired or replaced under 
warranty will be warranted for the remainder of the period prior to the first 
scheduled replacement point for the part. 

•  Add  on  or  modified  parts  that  are  not  exempted  by  the  Air  Resources 

Board may not be used.  The use of any nonexempted add on or modified 

parts by the owner will be grounds for disallowing a warranty claim.  The 
manufacturer will not be liable to warrant failures of warranted parts 
caused by the use of a nonexempted add on or modified part.

Summary of Contents for 6015BCE

































Reviews: