OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS
CRT Models
Page 8
800-345-6007
OPERATION
PRE-START INSPECTION
1. Make sure all safety guards are in place and all nuts and bolts
are secure.
2. check oil level in engine crankcase. See your engine manual for
procedure and specifications.
3. Inspect air cleaner for cleanliness. See your engine manual for
procedure.
4. check the fuel supply. Fill the fuel tank no closer than 1 inch
from top of tank to provide space for expansion. See your engine
manual for fuel recommendations.
5. Be sure spark plug wire is attached and spark plug is
tightened securely.
6. check position of wheels and wheel lockouts.
7. check depth regulator lever position.
8. Examine underneath and around engine for signs of oil or fuel
leaks.
9. Inspect fuel hoses for tightness and fuel seepage.
10. Look for signs of engine damage.
11. Remove excessive debris from muffler area and recoil starter.
START-UP
The controls required to start and run the rototiller are located on the
engine and are marked “choke” and “Throttle”.
A more detailed description of engine operation and all related
precautions and procedures can be found in the engine manufacturer’s
manual that accompanies each tiller.
COld STARTS
1. Move choke lever to full choke position.
2. Move throttle lever to “start”.
3. Pull starting rope out slowly one time and allow to return
normally.
4. Pull starting rope out rapidly, and allow rope to return normally.
5. When engine starts, gradually move choke lever to “no choke”
position and increase throttle speed.
RESTARTING A WARm ENGINE
Restarting an engine that is already warm from previous running does
not normally require use of the choke.
1. Move throttle lever to “start” position.
2. Pull starting rope out rapidly until engine starts. Allow rope to return
normally. Repeat until engine starts.
3. Adjust throttle speed to “high” for best tiller action.
PlEASE dO NOT START YOUR TIllER UNTIl
YOU hAvE REAd ThE mANUAl ThAT CAmE
WITh YOUR ENGINE, ANd ThE SECTIONS IN ThIS
mANUAl TITlEd CONTROlS, AdjUSTmENTS ANd
SAFETY. IF YOU hAvE REAd ThESE, FOllOW ThE
STEPS BElOW TO START YOUR TIllER. AlWAYS
PERFORm ThIS PRE-START ChECklIST BEFORE
STARTING ThE ENGINE.
GASOlINE IS hIGhlY FlAmmABlE ANd mUST
BE hANdlEd WITh CARE. NEvER FIll ThE TANk
WhEN ThE ENGINE IS hOT OR RUNNING. AlWAYS
mOvE OUTdOORS TO FIll ThE TANk.
WhEElS mUST AlWAYS BE lOCkEd IN ThE
TIllING POSITION WhEN ENGINE IS RUNNING.
dO NOT OPERATE ThE TIllER WITh ThE WhEEl
lOCkOUTS UNlOCkEd. AlWAYS SET ThE
WhEElS IN TIllING POSITION BEFORE STARTING
ENGINE.
AlWAYS PUT ThE dEPTh REGUlATOR lEvER IN
ThE TRANSPORT POSITION BEFORE STARTING
ENGINE. TINES ShOUld ClEAR ThE GROUNd.
ImPORTANT
ENGINE IS ShIPPEd FROm FACTORY WIThOUT OIl.
YOU mUST Add ENGINE OIl BEFORE STARTING
ENGINE.
AlWAYS kEEP hANdS ANd FEET ClEAR OF
ROTATING mAChINE PARTS.
CAUTION
!
WARNING
!
dANGER
!
Summary of Contents for 5055 6 HP
Page 27: ......
