Eagle Strata 128 Plus Install And Operation Instructions Download | Manualshive

Page: 13 / 40

background image

13

3 amp

FUSE

12 VOLT

BATTERY

BLACK

WIRE

RED

WIRE

TO SPEED/TEMP

SENSOR

(STRATA 128 PLUS &

STRATAVIEW ONLY)

POWER CONNECTIONS - Permanent mount units only
This unit works from a 12 volt DC system only. For the best results, run the
power cable directly to the boat’s battery. Keep the power cable away from
other boat wiring, especially the engine’s wires. This will give the best
isolation from electrical noise. If the supplied cable is not long enough to
reach the battery, splice #18 gauge insulated wire to it. You can attach the
power cable to an accessory or power buss, however, you may have
problems with electrical interference. Make certain to attach the in-line fuse
holder to the positive lead as close to the battery or terminal strip as
possible. This will protect both the unit and the power cable in the event of
a short. Use a 3-amp fuse.

WARNING!

Do not use this product without a 3-amp fuse wired into the power cable!
Failure to use a 3-amp fuse will void your warranty!

This unit has reverse polarity protection. No damage will occur if the power
wires are reversed. However, the unit will not work until the wires are
attached correctly.

TO SONAR UNIT

«
...
11
12
13
14
15
...
»

Summary of Contents for Strata 128 Plus









































Reviews:

No comments

Related manuals for Strata 128 Plus

Brand: Marcum Technologies Pages: 26

Brand: Furuno Pages: 92

Brand: Furuno Pages: 98

Brand: Lowrance Pages: 16

Brand: iXBlue Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands