Eagle PA5060E, Installation And Operating Instructions Manual

Page: 5 / 6

1. DC Power Connector 7. Aerial Connector Module A
2. Mains Power Connector 8. Tuner Module
3. Audio Output Sockets Module B 9. Blanking Plate
4. Aerial Connector Module B 10. Module Selector
5. Output Mode Selector 11. Power Indicator
6. Audio Output Sockets Module A 12. Mains Power On/Off Switch
5
PA5200C REAR PANEL
OUT IN
IN
OUT
LOGIC
PA5200C FRONT PANEL
EJECT
EJECT
PROGRAM
A SA
POWER
PROGRAM
AUTO-REVERSE
Background Music Cassette Player
AUTO-REVERSE
Background Music Cassette Player
S
1 5 2 7 3 4 6
WIRING OF PA5200C
Single Unit Operation
For single unit operation, set the mode selector switch located on the rear panel to
the ‘SA’ position. The two Phono type sockets marked “OUT’ on the rear panel are
the signal output sockets, although two sockets are supplied the output signal is
mono. It is not necessary to use both of these sockets when wiring to mono
amplifiers.
Three unit operation
For two or three unit operation one unit must be designated the master unit, this can
be done by moving the mode selector switch on the front panel to the ‘M’ position,
all other units must be switched to slave mode, this is done by moving the selector
to the ‘S’ position. The wiring of the units must be as per the diagram opposite. The
two Phono type sockets marked ‘OUT’ on the rear panel of the final slave are the
signal output sockets, although two sockets are supplied the output signal is mono.
It is not necessary to use both of these sockets when wiring to mono amplifiers.
Operation
To operate just insert a cassette in to one of the cassette decks (of the master unit if
more than one unit is being used), the cassette will start playing, if further cassettes
are inserted into the remaining decks the machine will play the first side if the current
deck, auto-reverse and play the second side of the current deck and at the end of
this side switch to the next deck in the chain. If a deck is empty then the machine
will ignore this deck.
OUT
OUT
OUT
IN
IN
IN
MASTER UNIT
SLAVE UNIT
SLAVE UNIT
LOGIC
LOGIC
LOGIC
IN
IN
IN
OUT
OUT
OUT
TO AUX INPUT OF AMPLIFIER
OUT
OUT
IN
IN
TO AUX INPUT OF AMPLIFIER
LOGIC
9 10
8
1. DC Connector 7. Cassette Decks
2. Mains Connector 8. Power on Indicator
3. Audio Out Socket 9. Mode Selector Switch
4. Audio In Socket 10. Mains on/off switch
5. Logic Out Socket
6. Logic In Socket
Operation
For Operation of the Tuner module and for aerial connection please refer to the earlier section.
Output Mode Selector
This switch is provided to enable the user to use either two separate Aux inputs or one single Aux input on an amplifier.
In the ‘separate’ position each module will only have an output signal present on its own output sockets, this allows the modules to be connected either to two Aux
inputs in one amplifier giving a volume control for each module. Alternatively these outputs could be wired to two separate amplifiers giving different music sources
for different areas. In this mode of operation the module selector switch must be set to the “BOTH’ position.
In the ‘mix’ position the output sockets of module A and module B are linked together internally, this allows the user to use both modules into one Aux input on an
amplifier. In this mode of operation the module selector switch must be set to the module currently in use.
Although two audio output sockets are supplied for each module, the output signal is mono. It is not necessary to use both these sockets when wiring to mono
amplifiers.
5 6 9 8 3 4 7 10 12 11
PA5200CT REAR PANEL PA5200CT FRONT PANEL
SEPARATE MIX
OUT
OUT
FM
FM
AM
AM
6
STATIONS PRESET
AM/FM TUNER
AM FM
BOTH
A B
POWER
1 2