a) Remove inner two screws from each end of tabletop.
b) Align tabletop holes from which original screws were just removed
with tubing assembly holes. Using #300794 screws supplied,
secure tubing assemblies to the tabletop as shown in Figure 1.
a) Place Lexan
®
canopy onto top of the horizontal tube of both tubing
assemblies, aligning all relevant holes.
b) Place oak top board onto top of Lexan
®
canopy until desired
location is achieved. Secure both the Lexan
®
canopy and the oak
top board to the tubing assemblies, using two #320647 screws per
end through the bottom of the horizontal tube and into the oak top
board, and two #313433 screws through the center holes in the
Lexan
®
canopy – see Figure 4.
c) On one end of table, place Lexan
®
close-off underneath Lexan
®
canopy. Align the three holes. Secure Lexan
®
close-off to the inner
side of the tubing assembly and into oak side panel, using three
#320647 screws – see Figure 5.
d) Repeat Step 3c to assemble remaining Lexan
®
close-off to
remaining end of table.
a) On one end of table, place oak side panel against outer side of
tubing assembly. Secure with two #320647 screws through vertical
tube of tubing assembly and into oak side panel as shown in Figure
2, using the 2nd and 3rd holes from the bottom.
b) Align designated hole in bottom cover plate with bottommost hole
in tubing assembly. Using one #320647 screw, secure bottom cover
plate to bottom plate of tubing assembly – see Figure 3. Screw
through bottom cover plate and into oak side panel.
c) Repeat Steps 2a & 2b to assemble remaining oak side panel to
remaining tubing assembly.
Figure 1
tubing assemblies
#300794
screws
tabletop
Figure 2
vertical
tube of
tubing assembly
oak
side
panel
#320647
screws
Figure 5
Figure 3
bottom
cover
plate
bottom plate
of tubing
assembly
#320647 screw
a) On one side of table, place oak front board onto outer edge of
Lexan
®
canopy.
b) On each end of table, align holes of Lexan
®
close-off and canopy.
Secure both Lexan
®
pieces to oak front board, using #313433
screws through both Lexan
®
pieces and into oak front board – see
Figure 6.
c) In center of table, secure Lexan
®
canopy to oak front board, using
#313433 screw through Lexan
®
canopy and into oak front board –
see Figure 6.
d) Repeat Steps 4a thru 4c to assemble remaining oak front board to
remaining side of table.
Seal all cracks and joints with NSF-approved sealant/caulk.
Figure 4
oak top
board
Lexan
®
canopy
horizontal
tube of
tubing
assembly
#320647
screws
#320647 screws
Lexan
®
close-off
Figure 6
#313433
screws
oak front board
#320647
screws
#313433
screws
1
Tubing Assemblies
2
Oak Side Panels
3
Assemble Canopy and Oak Top Board
4
Assemble Oak Front Boards
5
Sealing
Eagle Foodservice Equipment, Eagle MHC, Level-Lok Inc., and SpecFAB are divisions of Eagle Group. ©2002 by the Eagle Group
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A. • www.eaglegrp.com
• Phone: 302/653-3000 • (Fdsrv) 800/441-8440 • (MHC/Retail) 800/637-5100 • Fax: 302/653-2065 or 302/653-3036
ASSEMBLY INSTRUCTIONS
Lexan
®
Canopy
