Firmware update
Mixer type and ESC/motor protocol
Default PID setting
3.Open the Device Manager of your computer, find the Ports, please make sure the Com port
Serial Number is under 255, otherwise it will can't connect to the BLHELISUITE. You can change
the port serial number like the bellowing step :
Flight controller firmware update
1.Install latest STM32 Virtual COM Port Driver
2.Install STM BOOTLOAD Driver (STM Device in DFU MODE)
3.Open Betaflight configurator and choose firmware target “CrazybbeF4FS(Legacy)”,then select
the firmware version.
4.There are 2 ways to get in DFU Mode: 1). solder the boot pad and then plug USB to computer 2).
loading betaflight firmware and hit “flash”, then it will getting into DFU Mode automatically.
5.Open Zadig tools to replace the drivers from STM32 Bootloader to WINUSB Driver.
6.Reconnect the flight controller to the computer after replace driver done , and open
Betaflight Configurator, loading firmware and flash.
http://www.st.com/web/en/catalog/tools/PF257938
VTX Bands and Channels setup
Frequency
and
channel
frequency
table
:
CH
FR
Band1(A)
Band2(B)
Band3(E)
Band4(F)
Band5(R)
CH1
5865M
5733M
5705M
5740M
5658M
CH2
5845M
5752M
5685M
5760M
5695M
CH3
5825M
5771M
5665M
5780M
5732M
CH4
5805M
5790M
5665M
5800M
5769M
CH5
5785M
5809M
5885M
5820M
5806M
CH6
5765M
5828M
5905M
5840M
5843M
CH7
5745M
5847M
5905M
5860M
5880M
CH8
5725M
5866M
5905M
5880M
5917M
There are 2 ways to switch the vtx channels:
1.
If we need to use Channel 5705 then we should
Go to Betaflight CLI,type the command:
Set VTX_band=3
Set VTX_channel=1
save
2
.Disarm the UZ65 and then move the stick of the transmitter(THR MID+YAW LEFT+PITCH UP)to
enter OSD Menu,Enter to Features,then enter to VTX SA to set VTX Band and channel
1.Download New release Blhelisuite from:
2.Plug the usb and connect the flight controller to computer
https://www.mediafire.com/folder/dx6kfaasyo24l/BLHeliSuite
ESC Check and Flash firmware
Set one channel of your radio transmitter to activate the Flip over function in
the Mode tab of Betaflight configurator. The default Switch for Activate “Flip" is AUX4(Channel8)
Crashed
Disarm
The
Quad
Activate
Flip
over
Arm
The
Quad
Move
stick
to
flip
the
Quad
“Flip over after crash” procedure
Firmware update
Fix the CW propeller onto the M2
and M3 motor (CW motors)
Fix the CCW propellers onto the M1
and M4 motor (CCW motors)
Props Out
4.Open the BLHELISUITE, Select SILABS BLHeli Bootloader (Cleanflight) from the third tab on
the top side. Then Select the right Serial com port and Click connect. You can also Flash the new
release BLHeli_s firmware via the BLHEILISUITE, the firmware Target is “ -H- 0”
S
5
Notes:
RPM Filter has been enabled for the UZ65, so the ESC firmware is from JazzMaveric
(16.80 BLS) Link :https://github.com/JazzMaverick/BLHeli/tree/JazzMaverick-patch-1/BLHeli_
S%20SiLabs/Hex_files_16.8
Click check to see the
details of the 4in1 ESC
Firmware target
Flash firmware
Eachine UZ65 1
-
2S Brushless whoop Flysky version
