background image

7

INSTALLATION

DOMESTIC HOT WATER CONNECTION

Pressure reducer

If the water mains pressure is greater than 6 bar, a pressure reducer
calibrated to 4.5 bar must be fitted.

Safety unit

The tank safety unit must be ACV approved and calibrated to 7 bar.
The valve discharge must be connected to the waste water disposal
system.

Domestic hot water expassion tank

Installing a domestic hot water expansion tank avoids any risk of
overpressure due to pressure surges and also makes sure that
there is a always water flowing through the safety unit when refilling
the domestic hot water tank.

Hot water circulation

If the tank is located a long way from the point of use, then
installing a closed recirculation circuit ensures that a faster supply
of hot water is always available.

Descriptions

1.

Expansion relief valve

2.

Pressure reducing valve

3.

Thermostatic mixing valve

4.

Hot water secondary pump (it fitted)

5.

Non-return valve

6.

Hot water expansion vessel

7.

Stop cock

8.

Draw-off valve

9.

Drain cock

CONTROLLER KITS

KIT 1: ACV 13.00 / Basic

Basic kit for regulating initial flow temperature according to weather
conditions. It comprises: a temperature regulator with analogue
clock, wall-mounted water temperature sensor (-30/130 °C), external
sensor (-30/50 °C), 3-pin servomotor SQY 31 230 V and an
intermediate base.

KIT 2: ACV 13.00 / Standard

Basic kit for regulating initial flow temperature according to weather
conditions. It comprises: a temperature regulator with analogue
clock, wall-mounted water temperature sensor (-30/130 °C), external
sensor (-30/50 °C), 3-pin servomotor SQY 349,230 V and an
intermediate base.

1

2

4

6

5

7

9

8

3

IMPORTANT
As a safety measure against burns, we strongly advise
installing a thermostatic mixing valve (recommended
temperature: 60° C).

Optional fittings available

Groupe de sécurité

Ø 3/4”

Réducteur de pression

Ø 3/4“

Mitigeur thermostatique

Ø 3/4”

Vase d’expansion

5 litres

Summary of Contents for S 380

















Reviews: