background image

29

E-flite Shoestring 15e ARF Assembly Manual

WARRANTy REQUIREMENTS 

For Warranty consideration, you must include your 

original sales receipt verifying the proof-of-purchase 

date. 

Provided warranty conditions have been met, 

your Product will be serviced or replaced free of 

charge. Service or replacement decisions are at the 

sole discretion of Horizon.

NON-WARRANTy SERvICE

Should your service not be covered by warranty 

service will be completed and payment will be 

required without notification or estimate of the 

expense unless the expense exceeds 50% of the 

retail purchase cost. 

By submitting the item for service 

you are agreeing to payment of the service without 

notification. Service estimates are available upon 

request. You must include this request with your item 

submitted for service. Non-warranty service estimates 

will be billed a minimum of ½ hour of labor. In 

addition you will be billed for return freight. Horizon 

accepts money orders and cashiers checks, as well as 

Visa, MasterCard, American Express, and Discover 

cards. By submitting any item to Horizon for service, 

you are agreeing to Horizon’s Terms and Conditions 

found on our website http://www.horizonhobby.com/

Service/Request/.

UNITED STATES

(Electronics and engines)

Horizon Service Center

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

[email protected]

877-504-0233

Online Repair Request visit:

www.horizonhobby.com/service

(All other products)

Horizon Product Support

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

[email protected]

877-504-0233

UNITED KINGDOM

Horizon Hobby Limited

Units 1-4 Ployters Rd

Staple Tye

Harlow, Essex

CM18 7NS

United Kingdom

[email protected]

+44 (0) 1279 641 097

GERMANy

Horizon Technischer Service

Christian-Junge-Straße 1

25337 Elmshorn

Germany

[email protected]

+49 4121 46199 66

FRANCE

Horizon Hobby SAS

14 Rue Gustave Eiffel

Zone d’Activité du Réveil Matin

91230 Montgeron

+33 (0) 1 60 47 44 70

Compliance Information for the 

European Union

  

InstructIons for DIsposal of WEEE by 
usErs In thE EuropEan unIon

This product must not be disposed of with other waste. 

Instead, it is the user’s responsibility to dispose of their 

waste equipment by handing it over to a designated 

collection point for the recycling of waste electrical 

and electronic equipment. The separate collection 

and recycling of your waste equipment at the time 

of disposal will help to conserve natural resources 

and ensure that it is recycled in a manner that 

protects human health and the environment. For more 

information about where you can drop off your waste 

equipment for recycling, please contact your local city 

office, your household waste disposal service or where 

you purchased the product.

Academy of Model Aeronautics 

National Model Aircraft Safety Code

Effective January 1, 2011

A. GENERAL

A model aircraft is a non-human-carrying aircraft capable 

of sustained flight in the atmosphere. It may not exceed 

limitations of this code and is intended exclusively for sport, 

recreation and/or competition. All model flights must be 

conducted in accordance with this safety code and any 

additional rules specific to the flying site.

1. Model aircraft will not be flown:

(a) In a careless or reckless manner.
(b) At a location where model aircraft activities are 

prohibited.

2. Model aircraft pilots will:

(a) Yield the right of way to all man carrying aircraft.
b) See and avoid all aircraft and a spotter must be used 

when appropriate. (AMA Document #540-D-See and Avoid 

Guidance.)
(c) Not fly higher than approximately 400 feet above 

ground level within three (3) miles of an airport, without 

notifying the airport operator.
(d) Not interfere with operations and traffic patterns at any 

airport, heliport or seaplane base except where there is a 

mixed use agreement.
(e) Not exceed a takeoff weight, including fuel, of 55 

pounds unless in compliance with the AMA Large Model 

Aircraft program. (AMA Document 520-A)
(f) Ensure the aircraft is identified with the name and 

address or AMA number of the owner on the inside or 

affixed to the outside of the model aircraft. (This does not 

apply to model aircraft flown indoors).
(g) Not operate aircraft with metal-blade propellers or with 

gaseous boosts except for helicopters operated under the 

provisions of AMA Document #555.
(h) Not operate model aircraft while under the influence of 

alcohol or while using any drug which could adversely affect 

the pilot’s ability to safely control the model.
(i) Not operate model aircraft carrying pyrotechnic devices 

which explode or burn, or any device which propels a 

projectile or drops any object that creates a hazard to 

persons or property.

Summary of Contents for Shoestring 15e ARF

































Reviews: