E-FLITE Aeronca Champ 15E ARF Assembly Manual Download Page 9

Page: 9 / 36

E-flite Aeronca Champ 15e ARF Assembly Manual



24. Slide a silicone clevis retainer over a nylon

clevis. Remove the tape holding the aileron centered

to the wing. This is clear tape from the factory

so it might be difficult to see. Connect the aileron

servo to the receiver and use the radio system to

keep the aileron servo centered. Thread the clevis

on the pushrod wire and connect the clevis to the

aileron control horn. Adjust the clevis so the aileron

is aligned with the wing while the aileron servo is

centered. Slide the silicone clevis retainer over the

forks of the clevis to keep it from opening in flight.



25. Repeat Steps 1 through 24 to install the

remaining aileron servo and linkage.



26. If you have not done so, turn off the transmitter

and remove the power from the receiver.

Landing Gear Installation

Required Parts

Fuselage

Landing gear strut (2)

2mm locknut (6)

4mm locknut (2)

Side landing gear mount (4)

Bottom landing gear mount

2mm washer (12)

2mm x 12mm machine screw (6)

2.6mm x 10mm sheet metal screw (2)

3mm x 8mm machine screw (4)

Wheel collar (4mm) with setscrew (2)

Wheel with brass spacer, 2

-inch (63mm) (2)

Required Tools and Adhesives

Nut driver: 7mm

Ruler

Hemostat

Threadlock

Small flat blade screwdriver

Phillips screwdriver: #1

Hex wrench: 1.5mm



1. Remove the tape holding the front windscreen

on the fuselage. Remove the windscreen and set it

aside until it is time to glue it into position.

Make sure to use threadlock on all metal-to-

metal fasteners so they don’t vibrate loose.



2. Use a #1 Phillips screwdriver to tighten the

3mm x 8mm machine screws that attach the four

side landing gear mounts to the fuselage. There

are two mounts on the right and two on the left

side of the fuselage.



3. Attach the bottom landing gear mount to the

bottom of the fuselage using two 2.6mm x 10mm

sheet metal screws. Use a #1 Phillips screwdriver to

tighten the screws.

Summary of Contents for Aeronca Champ 15E ARF





































Search results

Summary of Contents for Aeronca Champ 15E ARF

Reviews:

Related manuals for Aeronca Champ 15E ARF

Brands by name

Popular brands

E-FLITE Aeronca Champ 15E ARF, Assembly Manual

Search results

Summary of Contents for Aeronca Champ 15E ARF

Reviews:

Related manuals for Aeronca Champ 15E ARF

Brands by name

Popular brands