Accessories
Self-Contained Dust Collection Systems
Service Kits
54290 “Bag-in-Box” System
•
95361
Air Line 5' long.
•
50682
Flex-Hose 1" dia. x 6' long.
•
95362
Rubber Connectors (5).
•
95575
Durable Box Receptacle.
•
Sample paper bag included.
Paper bag reorder:
50692
(400/case) or
50693
(24 per package.)
96122 Motor Tune-Up Kit:
•
Includes assorted parts to help
maintain and repair motor.
57260 Motor Repair Kit:
•
Contains special tools for
disassembly/assembly of machine.
50617, 56303 – 6' Long Flex-Hose Systems
•
50617:
Has
50683
Standard Reusable Felt Bag
with hook ’n loop end for easy emptying.
•
56303:
Has
56304
Zipper-Lock Bag.
Both systems include 6' long
50682
Flex-Hose.
Shown with optional
95361
Air Line (1/4").
DYNABRADE
®
DYNABRADE, INC.,
8989 Sheridan Drive
•
Clarence, NY 14031-1490
•
Phone: (716) 631-0100
•
Fax: 716-631-2073
•
International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
Zone Artisanale
•
L-5485 Wormeldange—Haut, Luxembourg
•
Telephone: 352 76 84 94 1
•
Fax: 352 76 84 95 1
© DYNABRADE, INC., 2004
PRINTED IN USA
PD00.26_Rev.1_01/04
Visit Our Web Sit:
www.dynabrade.com
Email:
Motor Disassembly/Assembly Instructions
(continued)
11.
Secure motor housing in vise, using
57092
Collar or padded jaws. Slide motor assembly into secured housing.
Note: With handle pointing toward you while looking into motor bore, be certain line-up pin enters slot to right side of center.
12.
Tighten
57332
Lock Ring with
56058
Lock Ring Tool to 34 N•m/300 on. - lbs. Attach shroud and weight-mated sanding pad.
13.
Apply one drop of #242 Loctite
®
(or equivalent) to threads of
96166
Set Screw and reinstall into
57332
Lock Ring. Do not over tighten.
To Disassemble Valve And Speed Regulator Assemblies:
1.
Invert tool and place in soft jaw vise or use
57092
Repair Collar.
2.
Loosen and remove
01788
Screws (2),
01211
Lock Washers (2) and
96421
Flat Washers from
56672
Adapter.
3.
Carefully remove
56672
Adapter making sure no parts fall to the ground. On non-vacuum and central vacuum models: pry off
54194
Muffler Cap and
remove
54195
Muffler (3).
4.
Remove
57343
Speed Regulator by detaching
98597
Retaining Ring with a pair of snap ring pliers. Remove
01024
O-Rings with a small screwdriver.
5.
Remove tip valve assembly from housing.
To Assemble Valve And Speed Regulator Assemblies:
1.
Lightly lubricate
01024
O-Rings and slide them on
57343
Speed Regulator. Install through regulator hole on
56672
Adapter. Place
98597
Retaining
Ring on groove of speed regulator using a pair of retaining ring pliers.
2.
Line up hole in valve stem with inlet hole in handle. Place
01464
Seal in handle. Insert
01472
Tip Valve so that metal pin goes through the valve stem.
Place
01468
Spring into the housing, small end first. Install
56673
Gasket and
96328
O-Ring.
3.
Gently line up
56672
Adapter onto handle so no parts shift when tightening. Replace and tighten
01788
Screws (2),
01211
Lock Washers (2), and
96421
Flat Washers (2).
Motor Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important:
Motor should operate at 12,000 RPM at 6.2 bar (90 PSIG). RPM should be checked with a tachometer. Before operating, we recommend
that 3-4 drops of pneumatic tool oil be placed directly into the air inlet with throttle lever depressed. Operate tool for 30 seconds to determine if machine is
operating properly and to allow lubricating oils to properly dispense through machine.
Loctite
®
is a registered trademark of the Loctite Corp.
01089 Safety Lock Lever
•
A
57375
Valve Stem must be used in
conjunction with this lever to
function properly.
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
